Re: [CAD_CAM_EDM_DRO] Help: Machine Control Software Advice
Posted by
Joe Vicars
on 2000-10-04 11:39:25 UTC
Don't forget your G-Code converter software too. If you are outputting .dxf you need a G-code converter before you can go to
CNCPro or DeskNC.
I think Yeager markets one called Ace Convert, and there's Gcode 2000 which is pretty good and cheap too.
Mike wrote:
CNCPro or DeskNC.
I think Yeager markets one called Ace Convert, and there's Gcode 2000 which is pretty good and cheap too.
Mike wrote:
> I've gone back over the archives looking for some clear recommendations on
> low-end step/direction machine control software and have found there are
> about as many opinions as there are packages.
>
> I'm looking to control a MAXNC 15 primarily to make 2-D panels with
> cutouts. There seems to be some consensus the MAXNC software is pretty
> bad. Further, the unipolar, non-chopper drive supplied by MAXNC is quite
> slow. So I'm leaning towards Dan Mauch's 2 amp or 5 amp controllers and
> some decent motors. The software choice, however, is a lot tougher.
>
> I currently use QuickCad (by Autodesk) for drawings. It would be great to
> import dxf files one way or another and be able to tweak the G-code and
> go. What do folks think of Yeager's CNC Pro? What about DeskNC? For more
> money, there are options like Bobcad. And finally, there's all the various
> DOS/Windows freeware like Kellyware's K-CAM, Stepster and Master Control
> CNC? I'm not crazy about Linux so EMC probably isn't a good choice.
>
> I hope I'm not beating a dead horse here, but you'd think there would be
> some standout software in this crowd? Has anyone had experience with
> several packages? I'm mainly looking for ease of use. Thanks!
>
> Mike
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
Discussion Thread
dave engvall
2000-10-03 21:40:18 UTC
Re: [CAD_CAM_EDM_DRO] Slightly off-topic : History behind lettered drills
catboat15@a...
2000-10-04 08:39:33 UTC
Re: [CAD_CAM_EDM_DRO] Slightly off-topic : History behind lettered drills
Mike
2000-10-04 11:29:44 UTC
Help: Machine Control Software Advice
Joe Vicars
2000-10-04 11:39:25 UTC
Re: [CAD_CAM_EDM_DRO] Help: Machine Control Software Advice
Chris Hellyar
2000-10-04 11:57:41 UTC
Re: [CAD_CAM_EDM_DRO] Help: Machine Control Software Advice
Alan Marconett KM6VV
2000-10-04 12:50:53 UTC
Re: [CAD_CAM_EDM_DRO] Help: Machine Control Software Advice
Rick Dulas
2000-10-04 13:59:36 UTC
Re: [CAD_CAM_EDM_DRO] Help: Machine Control Software Advice
ballendo@y...
2000-10-04 15:14:08 UTC
re:Help: Machine Control Software Advice
Mike
2000-10-04 16:39:05 UTC
Re: [CAD_CAM_EDM_DRO] Help: Machine Control Software Advice
cnc002@a...
2000-10-04 16:39:27 UTC
Re: [CAD_CAM_EDM_DRO] Help: Machine Control Software Advice
Carey L. Culpepper
2000-10-04 17:09:23 UTC
Re: [CAD_CAM_EDM_DRO] Help: Machine Control Software Advice
cnc002@a...
2000-10-04 18:05:58 UTC
Re: [CAD_CAM_EDM_DRO] Help: Machine Control Software Advice
Ozzie@h...
2000-10-04 20:26:00 UTC
Re: Help: Machine Control Software Advice
Chris Hellyar
2000-10-05 01:07:25 UTC
Re: [CAD_CAM_EDM_DRO] Help: Machine Control Software Advice
cnc002@a...
2000-10-05 12:27:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: Help: Machine Control Software Advice