Re: [CAD_CAM_EDM_DRO] Help: Machine Control Software Advice
Posted by
Alan Marconett KM6VV
on 2000-10-04 12:50:53 UTC
Mike, Joe,
If Mike has a MAXNC 15 does he already have the software and Unipolar
drivers? If so, there is a DXF to GCODE translator program on the disk
(as I recall). Someone a while ago was wanting to convert from 4-phase
to step/direction. Still want to do that? I'll eventually build a
circuit for step/direction to 4-phase, but that's much easier!
Alan
Joe Vicars wrote:
If Mike has a MAXNC 15 does he already have the software and Unipolar
drivers? If so, there is a DXF to GCODE translator program on the disk
(as I recall). Someone a while ago was wanting to convert from 4-phase
to step/direction. Still want to do that? I'll eventually build a
circuit for step/direction to 4-phase, but that's much easier!
Alan
Joe Vicars wrote:
>
> Don't forget your G-Code converter software too. If you are outputting .dxf you need a G-code converter before you can go to
> CNCPro or DeskNC.
> I think Yeager markets one called Ace Convert, and there's Gcode 2000 which is pretty good and cheap too.
>
> Mike wrote:
>
> > I've gone back over the archives looking for some clear recommendations on
> > low-end step/direction machine control software and have found there are
> > about as many opinions as there are packages.
> >
> > I'm looking to control a MAXNC 15 primarily to make 2-D panels with
> > cutouts. There seems to be some consensus the MAXNC software is pretty
> > bad. Further, the unipolar, non-chopper drive supplied by MAXNC is quite
> > slow. So I'm leaning towards Dan Mauch's 2 amp or 5 amp controllers and
> > some decent motors. The software choice, however, is a lot tougher.
> >
> > I currently use QuickCad (by Autodesk) for drawings. It would be great to
> > import dxf files one way or another and be able to tweak the G-code and
> > go. What do folks think of Yeager's CNC Pro? What about DeskNC? For more
> > money, there are options like Bobcad. And finally, there's all the various
> > DOS/Windows freeware like Kellyware's K-CAM, Stepster and Master Control
> > CNC? I'm not crazy about Linux so EMC probably isn't a good choice.
> >
> > I hope I'm not beating a dead horse here, but you'd think there would be
> > some standout software in this crowd? Has anyone had experience with
> > several packages? I'm mainly looking for ease of use. Thanks!
> >
> > Mike
> >
> > Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
> >
> > Addresses:
> > Post message: CAD_CAM_EDM_DRO@egroups.com
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> > Moderator: jmelson@... [Moderator]
> > URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> > FAQ: http://www.ktmarketing.com/faq.html
> > bill,
> > List Manager
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
Discussion Thread
dave engvall
2000-10-03 21:40:18 UTC
Re: [CAD_CAM_EDM_DRO] Slightly off-topic : History behind lettered drills
catboat15@a...
2000-10-04 08:39:33 UTC
Re: [CAD_CAM_EDM_DRO] Slightly off-topic : History behind lettered drills
Mike
2000-10-04 11:29:44 UTC
Help: Machine Control Software Advice
Joe Vicars
2000-10-04 11:39:25 UTC
Re: [CAD_CAM_EDM_DRO] Help: Machine Control Software Advice
Chris Hellyar
2000-10-04 11:57:41 UTC
Re: [CAD_CAM_EDM_DRO] Help: Machine Control Software Advice
Alan Marconett KM6VV
2000-10-04 12:50:53 UTC
Re: [CAD_CAM_EDM_DRO] Help: Machine Control Software Advice
Rick Dulas
2000-10-04 13:59:36 UTC
Re: [CAD_CAM_EDM_DRO] Help: Machine Control Software Advice
ballendo@y...
2000-10-04 15:14:08 UTC
re:Help: Machine Control Software Advice
Mike
2000-10-04 16:39:05 UTC
Re: [CAD_CAM_EDM_DRO] Help: Machine Control Software Advice
cnc002@a...
2000-10-04 16:39:27 UTC
Re: [CAD_CAM_EDM_DRO] Help: Machine Control Software Advice
Carey L. Culpepper
2000-10-04 17:09:23 UTC
Re: [CAD_CAM_EDM_DRO] Help: Machine Control Software Advice
cnc002@a...
2000-10-04 18:05:58 UTC
Re: [CAD_CAM_EDM_DRO] Help: Machine Control Software Advice
Ozzie@h...
2000-10-04 20:26:00 UTC
Re: Help: Machine Control Software Advice
Chris Hellyar
2000-10-05 01:07:25 UTC
Re: [CAD_CAM_EDM_DRO] Help: Machine Control Software Advice
cnc002@a...
2000-10-05 12:27:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: Help: Machine Control Software Advice