Re: Cheap DRO system using digital scales and a PC
Posted by
Lee Studley
on 2000-11-04 14:28:37 UTC
Hi,
You got me thinking, so I hooked up a 'cheapie' caliper to my scope
and found that the pins 1..4 agree with mitutoyo except my pin4 is
Vbat=1.5v. I was hoping for a standard slow baud rate about 110baud.
Whatever 1.5v micro is in there, its probably running off an RC
clock, but at slow bauds, rate error can be an acceptable percentage
of the overall transmitted packet.
Since its async format, but with an optional clock, translation may
not be needed, only voltage level translation which can be stolen
from the other serial port pins. I'll put it on the storage
scopes at work and figure it out. Probably sometime next week.
I bought this one as a quill DRO 6". Just have to keep it out
of the coolant...
-Lee
You got me thinking, so I hooked up a 'cheapie' caliper to my scope
and found that the pins 1..4 agree with mitutoyo except my pin4 is
Vbat=1.5v. I was hoping for a standard slow baud rate about 110baud.
Whatever 1.5v micro is in there, its probably running off an RC
clock, but at slow bauds, rate error can be an acceptable percentage
of the overall transmitted packet.
Since its async format, but with an optional clock, translation may
not be needed, only voltage level translation which can be stolen
from the other serial port pins. I'll put it on the storage
scopes at work and figure it out. Probably sometime next week.
I bought this one as a quill DRO 6". Just have to keep it out
of the coolant...
-Lee
--- In CAD_CAM_EDM_DRO@egroups.com, diazden <diazden@o...> wrote:
> Hello guys;
> here are the pin definitions on my mitutoyo vernier caliper
> pin n1 gnd, pin n2 data,pin n3 clock,pin n4 nc (it can be ground )
pin n5 request
> all the info come in a leaflet with the tool
> regards
> mariano
>
> > List Manager
Discussion Thread
Frans Nieuwerth
2000-11-03 11:54:45 UTC
Cheap DRO system using digital scales and a PC
Alan Marconett KM6VV
2000-11-03 14:28:18 UTC
Re: [CAD_CAM_EDM_DRO] Cheap DRO system using digital scales and a PC
Lee Studley
2000-11-03 19:27:19 UTC
Re: Cheap DRO system using digital scales and a PC
diazden
2000-11-04 10:11:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Cheap DRO system using digital scales and a PC
Lee Studley
2000-11-04 14:28:37 UTC
Re: Cheap DRO system using digital scales and a PC
Frans Nieuwerth
2000-11-06 13:11:38 UTC
Re: Cheap DRO system using digital scales and a PC
Lee Studley
2000-11-06 14:45:34 UTC
Re: Cheap DRO system using digital scales and a PC
Lee Studley
2000-11-06 21:54:14 UTC
Re: Cheap DRO system using digital scales and a PC
Wilfried Fedtke
2000-11-07 10:01:44 UTC
Re: Cheap DRO system using digital scales and a PC
Kos
2000-11-07 12:14:46 UTC
Re: Cheap DRO system using digital scales and a PC
diazden
2000-11-07 15:14:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Cheap DRO system using digital scales and a PC
Lee Studley
2000-11-07 15:33:33 UTC
Re: Cheap DRO system using digital scales and a PC
Lee Studley
2000-11-07 15:35:25 UTC
Re: Cheap DRO system using digital scales and a PC
Lee Studley
2000-11-07 15:37:06 UTC
Re: Cheap DRO system using digital scales and a PC
diazden
2000-11-07 15:42:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: Cheap DRO system using digital scales and a PC
wanliker@a...
2000-11-07 16:01:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Cheap DRO system using digital scales and a PC
Jon Elson
2000-11-07 16:02:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Cheap DRO system using digital scales and a PC
Lee Studley
2000-11-08 07:46:16 UTC
Re: Cheap DRO system using digital scales and a PC
wilfried.fedtke@t...
2000-11-08 09:00:34 UTC
Re:Re: Cheap DRO system using digital scales and a PC
Lee Studley
2000-11-08 09:42:17 UTC
Re:Re: Cheap DRO system using digital scales and a PC
diazden
2000-11-08 15:02:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: Cheap DRO system using digital scales and a PC
Wally K
2000-11-08 15:23:01 UTC
Re: Cheap DRO system using digital scales and a PC
Lee Studley
2000-11-08 16:21:31 UTC
Re: Cheap DRO system using digital scales and a PC
Frans Nieuwerth
2000-11-10 01:59:10 UTC
Re: Cheap DRO system using digital scales and a PC