Re: [CAD_CAM_EDM_DRO]A question of size managenent.
Posted by
Joe Vicars
on 2000-11-29 08:26:06 UTC
Sounds like a translator problem, or you may have a controller that doesn't support circlular interpolation. If your arc is truly a
portion of a circle, then yes, you should be able to replace all those G01 commands with G02/03.
If the arc is a spline then that is a different story. What translator/controller are you using?
BillDarby wrote:
portion of a circle, then yes, you should be able to replace all those G01 commands with G02/03.
If the arc is a spline then that is a different story. What translator/controller are you using?
BillDarby wrote:
> Hi All
>
> I recently ran a tool path with 36,000 lines of code. (no big deal in the real world) Now my question is this: This
> path was really only 200 sets of (a line an arc and a second line) or [line, arc, line, 200 times]. "If" I could have entered the
> summation of the 160 lines of code representing each arc into one common "arc command" I would have had a total of just 600 lines
> of code.
>
> As it was, there was not enough memory to edit on the CNC. It could run the program, but if I wanted to change anything I
> had to do the change on my off line program on my PC, then reload by floppy to the CNC.
>
> Is there any software that could convert all these line commands into arc commands?
>
> Just compelled to ask!!!
>
> Bill Darby
>
> Also (have never seen my CNC do this before) As these [160 line] arcs became smaller my CNC began what appeared like a series of
> jerky motions as it rounded these corners and sped up when it hit the straight-away. The cut looked and felt perfect but there
> definitely some jerking going on as the entire mill set up a rocking motion on the wooden floor. I almost thought the CPU was
> bogged down. The feed was set at 32 IPM and dropped to less then 1/3 rd on the corners.
>
> What do you think is going on??
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
Discussion Thread
BillDarby
2000-11-29 07:37:31 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
Marcus & Eva
2000-11-29 08:20:38 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
Joe Vicars
2000-11-29 08:26:06 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
Jon Elson
2000-11-29 12:05:43 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
BillDarby
2000-11-29 13:00:15 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
BillDarby
2000-11-29 15:36:31 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
Fred Smith
2000-11-29 16:06:35 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
BillDarby
2000-11-29 17:43:57 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
ballendo@y...
2000-11-29 17:58:16 UTC
Re: A question of size managenent.
Marcus & Eva
2000-11-29 20:27:28 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
Fred Smith
2000-11-29 20:29:12 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
BillDarby
2000-11-29 20:54:50 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
Jon Elson
2000-11-29 21:08:23 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
Jon Elson
2000-11-29 21:40:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: A question of size managenent.
BillDarby
2000-11-29 21:57:01 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
Jon Elson
2000-11-29 22:27:15 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
Fred Smith
2000-11-29 22:39:28 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
BillDarby
2000-11-30 06:28:17 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
Marcus & Eva
2000-11-30 08:04:52 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
Joe Fahy
2000-11-30 08:12:33 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
BillDarby
2000-11-30 08:26:15 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
Fred Smith
2000-11-30 12:02:40 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
Fred Smith
2000-11-30 12:17:10 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
BillDarby
2000-11-30 12:38:23 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.
ballendo@y...
2000-11-30 20:36:20 UTC
Re: A question of size managenent.
Marcus & Eva
2000-11-30 20:59:15 UTC
Re: [CAD_CAM_EDM_DRO]A question of size managenent.