Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Posted by
Jon Elson
on 2000-12-01 12:02:51 UTC
Jon Anderson wrote:
movement. You have a shaft keyed to a worm, worm wheel keyed to
shaft to overload clutch, overload clutch keyed to inner shaft keyed
to pinion, pinion to rack. Also, there is no expectation the quill
rack is ground to any sort of accuracy. I can';t imagine there would
be any use in putting an encoder or stepper on this. Might as well
just have a dc gear motor, or leave the power feed mechanism as is.
I can't even imagine any hobby use for something with .050"
backlash.
Jon
> Smoke wrote:There is often .050" backlash from the fine feed handle to the quill
> >
> > If you MUST drive the quill for your Z axis on a Bridgeport, I don't
> > see why you don't simly mount a pulley on the quills hadn feed and
> > run a belt to a stepper motor mounted on a bracket.
>
> This might be fine for a hobby setup
movement. You have a shaft keyed to a worm, worm wheel keyed to
shaft to overload clutch, overload clutch keyed to inner shaft keyed
to pinion, pinion to rack. Also, there is no expectation the quill
rack is ground to any sort of accuracy. I can';t imagine there would
be any use in putting an encoder or stepper on this. Might as well
just have a dc gear motor, or leave the power feed mechanism as is.
I can't even imagine any hobby use for something with .050"
backlash.
Jon
Discussion Thread
Jon Anderson
2000-11-30 17:09:26 UTC
Looking for short ballscrew
Hugh Currin
2000-12-01 08:11:24 UTC
Re: Looking for short ballscrew
Wally K
2000-12-01 08:46:02 UTC
Re: Looking for short ballscrew for Z axis
Jon Anderson
2000-12-01 09:11:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Jon Anderson
2000-12-01 09:14:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew for Z axis
ptengin@a...
2000-12-01 09:40:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Jon Anderson
2000-12-01 09:58:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Smoke
2000-12-01 10:17:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
William Scalione
2000-12-01 10:26:08 UTC
Re: Looking for short ballscrew
Jon Anderson
2000-12-01 10:36:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Jon Anderson
2000-12-01 10:42:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Smoke
2000-12-01 11:06:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
PMeinhard@a...
2000-12-01 11:49:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Jon Elson
2000-12-01 12:02:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Greg Nuspel
2000-12-01 12:08:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Jon Anderson
2000-12-01 13:30:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Smoke
2000-12-01 13:34:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Greg Nuspel
2000-12-01 14:00:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Smoke
2000-12-01 14:43:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Jon Elson
2000-12-01 15:03:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Greg Nuspel
2000-12-01 16:05:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Jon Anderson
2000-12-01 16:39:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Jon Elson
2000-12-01 22:58:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Jon Elson
2000-12-01 23:18:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
dave engvall
2000-12-03 22:37:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Smoke
2000-12-03 23:01:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Carey L. Culpepper
2000-12-05 09:25:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
ptengin@a...
2000-12-05 10:54:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Carey L. Culpepper
2000-12-05 11:11:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Jon Elson
2000-12-05 11:44:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for short ballscrew
Bill Griffin
2000-12-05 22:31:15 UTC
Re: Re: Looking for short ballscrew
ptengin@a...
2000-12-06 00:45:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Looking for short ballscrew