CAD CAM EDM DRO - Yahoo Group Archive

Re: Gecko 5V supply

Posted by Ray
on 2001-04-01 19:42:10 UTC
The Gecko 210 can be set up to accept either common ground or common +5.
The 201 needs +5 external. On my setup I use an external +5 power supply
and hook the +5 to Gecko common, the parport pins to dir and step, and the 0
volt from the external supply to a ground pin on the parport. I had to
change some jumpers on the inside of the drive. Mariss' instructions are
real good here.

HTH
Ray

From: jvicars@...

The Gecko 201 manual says that the 5V for step and direction must come
from the indexer/pulse source. I.E. the computer. I don't really
understand how to accomplish this. Can you get 5V through the
parallel port somehow, or do you have to run a 5V line from the
computer to the drivers?
Anybody have advice on how to hook this up?

Discussion Thread

jvicars@c... 2001-04-01 07:05:45 UTC Gecko 5V supply kleinbauer@j... 2001-04-01 07:30:15 UTC Re: Gecko 5V supply Dan Mauch 2001-04-01 07:56:57 UTC Re: [CAD_CAM_EDM_DRO] Gecko 5V supply kleinbauer@j... 2001-04-01 08:06:54 UTC Re: Gecko 5V supply mariss92705@y... 2001-04-01 13:42:03 UTC Re: Gecko 5V supply Brian Pitt 2001-04-01 16:04:05 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply jesse 2001-04-01 18:00:52 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply kleinbauer@j... 2001-04-01 18:28:27 UTC Re: Gecko 5V supply You gotta have ground! jesse 2001-04-01 19:13:48 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply You gotta have ground! Ray 2001-04-01 19:42:10 UTC Re: Gecko 5V supply Alan Marconett KM6VV 2001-04-02 11:18:11 UTC Gecko 5V supply Dan Mauch 2001-04-02 11:18:24 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply Brian Pitt 2001-04-02 12:18:41 UTC Re: [CAD_CAM_EDM_DRO] Gecko 5V supply Tom Eldredge 2001-04-03 07:06:17 UTC Re: [CAD_CAM_EDM_DRO] Gecko 5V supply Tim Goldstein 2001-04-03 08:59:13 UTC RE: [CAD_CAM_EDM_DRO] Gecko 5V supply Alan Marconett KM6VV 2001-04-03 10:58:21 UTC Re: [CAD_CAM_EDM_DRO] Gecko 5V supply Tom Eldredge 2001-04-03 16:53:25 UTC Re: [CAD_CAM_EDM_DRO] Gecko 5V supply Terry Toddy 2001-04-04 06:09:46 UTC Re: [CAD_CAM_EDM_DRO] Gecko 5V supply Doug Fortune 2001-04-04 07:08:14 UTC Gecko 5V supply Doug Harrison 2001-04-04 14:34:12 UTC Re: [CAD_CAM_EDM_DRO] Gecko 5V supply Alan Marconett KM6VV 2001-04-04 15:24:30 UTC Re: [CAD_CAM_EDM_DRO] Gecko 5V supply dave engvall 2001-04-04 22:20:50 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply Tom Eldredge 2001-04-05 03:51:02 UTC Re: [CAD_CAM_EDM_DRO] Gecko 5V supply Jon Elson 2001-04-05 21:58:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply