CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Gecko 5V supply

Posted by Terry Toddy
on 2001-04-04 06:09:46 UTC
Hello all,

There has been much discussion on how to make a 5 volt supply to avoid
using the pc's power supply. How do you use the external power supply
with the Gecko G201? Someone mentioned opening up the drive and changing
a jumper? More information on this would be greatly appreciated.

Terry Toddy

Alan Marconett KM6VV wrote:
>
> Hi Tom,
>
> Weird Stuff in Sunnyvale, CA has them for $5 "in the back". I don't
> know what they sell through the mail.
>
> http://www.weirdstuff.com/
>
> Alan KM6VV
>
> Tom Eldredge wrote:
> >
> > Gentlemen,
> >
> > Where can you get cheap 5volt wall warts? I see the 4.5 and 6 volt ones all
> > the time, but 5v? They seem to run around $25.00 USD. I can get a used PC
> > power supply for 5-10 USD. And that is a regulated power supply with a
> > chord and power off switch.
> >
> > Tom Eldredge
> >

Discussion Thread

jvicars@c... 2001-04-01 07:05:45 UTC Gecko 5V supply kleinbauer@j... 2001-04-01 07:30:15 UTC Re: Gecko 5V supply Dan Mauch 2001-04-01 07:56:57 UTC Re: [CAD_CAM_EDM_DRO] Gecko 5V supply kleinbauer@j... 2001-04-01 08:06:54 UTC Re: Gecko 5V supply mariss92705@y... 2001-04-01 13:42:03 UTC Re: Gecko 5V supply Brian Pitt 2001-04-01 16:04:05 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply jesse 2001-04-01 18:00:52 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply kleinbauer@j... 2001-04-01 18:28:27 UTC Re: Gecko 5V supply You gotta have ground! jesse 2001-04-01 19:13:48 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply You gotta have ground! Ray 2001-04-01 19:42:10 UTC Re: Gecko 5V supply Alan Marconett KM6VV 2001-04-02 11:18:11 UTC Gecko 5V supply Dan Mauch 2001-04-02 11:18:24 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply Brian Pitt 2001-04-02 12:18:41 UTC Re: [CAD_CAM_EDM_DRO] Gecko 5V supply Tom Eldredge 2001-04-03 07:06:17 UTC Re: [CAD_CAM_EDM_DRO] Gecko 5V supply Tim Goldstein 2001-04-03 08:59:13 UTC RE: [CAD_CAM_EDM_DRO] Gecko 5V supply Alan Marconett KM6VV 2001-04-03 10:58:21 UTC Re: [CAD_CAM_EDM_DRO] Gecko 5V supply Tom Eldredge 2001-04-03 16:53:25 UTC Re: [CAD_CAM_EDM_DRO] Gecko 5V supply Terry Toddy 2001-04-04 06:09:46 UTC Re: [CAD_CAM_EDM_DRO] Gecko 5V supply Doug Fortune 2001-04-04 07:08:14 UTC Gecko 5V supply Doug Harrison 2001-04-04 14:34:12 UTC Re: [CAD_CAM_EDM_DRO] Gecko 5V supply Alan Marconett KM6VV 2001-04-04 15:24:30 UTC Re: [CAD_CAM_EDM_DRO] Gecko 5V supply dave engvall 2001-04-04 22:20:50 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply Tom Eldredge 2001-04-05 03:51:02 UTC Re: [CAD_CAM_EDM_DRO] Gecko 5V supply Jon Elson 2001-04-05 21:58:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply