RE: [CAD_CAM_EDM_DRO] Gecko 5V supply
Posted by
Tim Goldstein
on 2001-04-03 08:59:13 UTC
You can take a 9 v or so wall wart and run it through a $1.00 or less
voltage regulator (7805 would do the trick and you can even get them from
Rat Shack). You will then have a nice regulated power supply for very little
cost.
Tim
[Denver, CO]
voltage regulator (7805 would do the trick and you can even get them from
Rat Shack). You will then have a nice regulated power supply for very little
cost.
Tim
[Denver, CO]
> Gentlemen,
>
> Where can you get cheap 5volt wall warts? I see the 4.5 and
> 6 volt ones all
> the time, but 5v? They seem to run around $25.00 USD. I can
> get a used PC
> power supply for 5-10 USD. And that is a regulated power
> supply with a
> chord and power off switch.
>
> Tom Eldredge
>
> FAQ: http://www.ktmarketing.com/faq.html
Discussion Thread
jvicars@c...
2001-04-01 07:05:45 UTC
Gecko 5V supply
kleinbauer@j...
2001-04-01 07:30:15 UTC
Re: Gecko 5V supply
Dan Mauch
2001-04-01 07:56:57 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
kleinbauer@j...
2001-04-01 08:06:54 UTC
Re: Gecko 5V supply
mariss92705@y...
2001-04-01 13:42:03 UTC
Re: Gecko 5V supply
Brian Pitt
2001-04-01 16:04:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply
jesse
2001-04-01 18:00:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply
kleinbauer@j...
2001-04-01 18:28:27 UTC
Re: Gecko 5V supply You gotta have ground!
jesse
2001-04-01 19:13:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply You gotta have ground!
Ray
2001-04-01 19:42:10 UTC
Re: Gecko 5V supply
Alan Marconett KM6VV
2001-04-02 11:18:11 UTC
Gecko 5V supply
Dan Mauch
2001-04-02 11:18:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply
Brian Pitt
2001-04-02 12:18:41 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
Tom Eldredge
2001-04-03 07:06:17 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
Tim Goldstein
2001-04-03 08:59:13 UTC
RE: [CAD_CAM_EDM_DRO] Gecko 5V supply
Alan Marconett KM6VV
2001-04-03 10:58:21 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
Tom Eldredge
2001-04-03 16:53:25 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
Terry Toddy
2001-04-04 06:09:46 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
Doug Fortune
2001-04-04 07:08:14 UTC
Gecko 5V supply
Doug Harrison
2001-04-04 14:34:12 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
Alan Marconett KM6VV
2001-04-04 15:24:30 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
dave engvall
2001-04-04 22:20:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply
Tom Eldredge
2001-04-05 03:51:02 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
Jon Elson
2001-04-05 21:58:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply