Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply
Posted by
Dan Mauch
on 2001-04-02 11:18:24 UTC
Unless I am really behind the times all of the previous PC power supplies
have circuitry that shuts down the power supply if it detects a short
circuit.
Dan
-----Original Message-----
From: Brian Pitt <bfp@...>
To: CAD_CAM_EDM_DRO@yahoogroups.com <CAD_CAM_EDM_DRO@yahoogroups.com>
Date: Sunday, April 01, 2001 4:04 PM
Subject: Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply
have circuitry that shuts down the power supply if it detects a short
circuit.
Dan
-----Original Message-----
From: Brian Pitt <bfp@...>
To: CAD_CAM_EDM_DRO@yahoogroups.com <CAD_CAM_EDM_DRO@yahoogroups.com>
Date: Sunday, April 01, 2001 4:04 PM
Subject: Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply
>discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>a note of caution on this one , tripple check everything
>
>the +5V on the game port is usually tied directly to the power supply
>rails on the PC bus and can pull the full amperage of the supply in a
>'dead short' circuit (up to 25A@5V)
>it might not kill you but it wont be too good for the PC if a wire gets
>crossed
>
>Brian
>
>On Sunday 01 April 2001 13:41, you wrote:
>> Hi,
>>
>> Most PCs have a game port. The +5VDC is available on pin of the game
>> port. You cannot electrocute yourself off of 5 volts even if you put
>> the wires in your mouth and stand in a tub of salt water. Haven't
>> tried it myself but I am sure.
>>
>> Mariss
>
>Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
>
>Addresses:
>Post message: CAD_CAM_EDM_DRO@yahoogroups.com
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
>Moderator: jmelson@... timg@... [Moderator]
>URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>bill,
>List Manager
>
>FAQ: http://www.ktmarketing.com/faq.html
>
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>
Discussion Thread
jvicars@c...
2001-04-01 07:05:45 UTC
Gecko 5V supply
kleinbauer@j...
2001-04-01 07:30:15 UTC
Re: Gecko 5V supply
Dan Mauch
2001-04-01 07:56:57 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
kleinbauer@j...
2001-04-01 08:06:54 UTC
Re: Gecko 5V supply
mariss92705@y...
2001-04-01 13:42:03 UTC
Re: Gecko 5V supply
Brian Pitt
2001-04-01 16:04:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply
jesse
2001-04-01 18:00:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply
kleinbauer@j...
2001-04-01 18:28:27 UTC
Re: Gecko 5V supply You gotta have ground!
jesse
2001-04-01 19:13:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply You gotta have ground!
Ray
2001-04-01 19:42:10 UTC
Re: Gecko 5V supply
Alan Marconett KM6VV
2001-04-02 11:18:11 UTC
Gecko 5V supply
Dan Mauch
2001-04-02 11:18:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply
Brian Pitt
2001-04-02 12:18:41 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
Tom Eldredge
2001-04-03 07:06:17 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
Tim Goldstein
2001-04-03 08:59:13 UTC
RE: [CAD_CAM_EDM_DRO] Gecko 5V supply
Alan Marconett KM6VV
2001-04-03 10:58:21 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
Tom Eldredge
2001-04-03 16:53:25 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
Terry Toddy
2001-04-04 06:09:46 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
Doug Fortune
2001-04-04 07:08:14 UTC
Gecko 5V supply
Doug Harrison
2001-04-04 14:34:12 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
Alan Marconett KM6VV
2001-04-04 15:24:30 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
dave engvall
2001-04-04 22:20:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply
Tom Eldredge
2001-04-05 03:51:02 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
Jon Elson
2001-04-05 21:58:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply