Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply
Posted by
Brian Pitt
on 2001-04-01 16:04:05 UTC
a note of caution on this one , tripple check everything
the +5V on the game port is usually tied directly to the power supply
rails on the PC bus and can pull the full amperage of the supply in a
'dead short' circuit (up to 25A@5V)
it might not kill you but it wont be too good for the PC if a wire gets
crossed
Brian
the +5V on the game port is usually tied directly to the power supply
rails on the PC bus and can pull the full amperage of the supply in a
'dead short' circuit (up to 25A@5V)
it might not kill you but it wont be too good for the PC if a wire gets
crossed
Brian
On Sunday 01 April 2001 13:41, you wrote:
> Hi,
>
> Most PCs have a game port. The +5VDC is available on pin of the game
> port. You cannot electrocute yourself off of 5 volts even if you put
> the wires in your mouth and stand in a tub of salt water. Haven't
> tried it myself but I am sure.
>
> Mariss
Discussion Thread
jvicars@c...
2001-04-01 07:05:45 UTC
Gecko 5V supply
kleinbauer@j...
2001-04-01 07:30:15 UTC
Re: Gecko 5V supply
Dan Mauch
2001-04-01 07:56:57 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
kleinbauer@j...
2001-04-01 08:06:54 UTC
Re: Gecko 5V supply
mariss92705@y...
2001-04-01 13:42:03 UTC
Re: Gecko 5V supply
Brian Pitt
2001-04-01 16:04:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply
jesse
2001-04-01 18:00:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply
kleinbauer@j...
2001-04-01 18:28:27 UTC
Re: Gecko 5V supply You gotta have ground!
jesse
2001-04-01 19:13:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply You gotta have ground!
Ray
2001-04-01 19:42:10 UTC
Re: Gecko 5V supply
Alan Marconett KM6VV
2001-04-02 11:18:11 UTC
Gecko 5V supply
Dan Mauch
2001-04-02 11:18:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply
Brian Pitt
2001-04-02 12:18:41 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
Tom Eldredge
2001-04-03 07:06:17 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
Tim Goldstein
2001-04-03 08:59:13 UTC
RE: [CAD_CAM_EDM_DRO] Gecko 5V supply
Alan Marconett KM6VV
2001-04-03 10:58:21 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
Tom Eldredge
2001-04-03 16:53:25 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
Terry Toddy
2001-04-04 06:09:46 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
Doug Fortune
2001-04-04 07:08:14 UTC
Gecko 5V supply
Doug Harrison
2001-04-04 14:34:12 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
Alan Marconett KM6VV
2001-04-04 15:24:30 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
dave engvall
2001-04-04 22:20:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply
Tom Eldredge
2001-04-05 03:51:02 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 5V supply
Jon Elson
2001-04-05 21:58:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 5V supply