Re: which steppers to buy?
Posted by
Tony Jeffree
on 2001-05-28 03:06:49 UTC
At 03:30 28/05/2001 +0000, you wrote:
of table travel per motor step - or half-step) of the system, and will also
change the maximum rate of travel that can be achieved.
If you're not after high rates of travel, using a smaller motors & a
reduction drive may well be a cheaper solution (cheaper motors, cheaper
drive electronics, etc).
Regards,
Tony
> >Not the same. Changing the drive ratio will change the resolution (inches
> > Ok Group every one is saying to use at least a 200oz
> > stepper .I called Smithy and asked then what they
> > would suggest stepper s for the 17X20 3 in 1 they sell
> > I was told that a 150 oz stepper and a 3:1 timing gear
> > now I am confused is this rating they say too small I
> > do have these stepper s now.
>
>Isn't that the same as a 450 Oz stepper? If you gear the stepper
>1, and the screw at 3, that multiplies things, torque-wise.
>Maybe 1-1 ratio and a 200 oz stepper is all that is needed.
of table travel per motor step - or half-step) of the system, and will also
change the maximum rate of travel that can be achieved.
If you're not after high rates of travel, using a smaller motors & a
reduction drive may well be a cheaper solution (cheaper motors, cheaper
drive electronics, etc).
Regards,
Tony
Discussion Thread
jh1221@a...
2001-05-27 06:53:14 UTC
which steppers to buy?
RC
2001-05-27 09:12:24 UTC
Re: [CAD_CAM_EDM_DRO] which steppers to buy?
Tim Goldstein
2001-05-27 09:27:17 UTC
RE: [CAD_CAM_EDM_DRO] which steppers to buy?
Tim Goldstein
2001-05-27 09:32:21 UTC
RE: [CAD_CAM_EDM_DRO] which steppers to buy?
RC
2001-05-27 09:37:34 UTC
Re: [CAD_CAM_EDM_DRO] which steppers to buy?
marble here
2001-05-27 19:40:44 UTC
RE: [CAD_CAM_EDM_DRO] which steppers to buy?
Jerry Kimberlin
2001-05-27 19:48:58 UTC
Re: [CAD_CAM_EDM_DRO] which steppers to buy?
Chris Stratton
2001-05-27 20:18:39 UTC
Re: [CAD_CAM_EDM_DRO] which steppers to buy?
Tim Goldstein
2001-05-27 20:27:43 UTC
RE: [CAD_CAM_EDM_DRO] which steppers to buy?
Tim Goldstein
2001-05-27 20:29:57 UTC
RE: [CAD_CAM_EDM_DRO] which steppers to buy?
Jon Elson
2001-05-27 20:57:54 UTC
Re: [CAD_CAM_EDM_DRO] which steppers to buy?
Jon Elson
2001-05-27 21:00:37 UTC
Re: [CAD_CAM_EDM_DRO] which steppers to buy?
Hugh & Denise Currin
2001-05-27 22:53:08 UTC
Re: which steppers to buy?
Ian Wright
2001-05-28 01:28:49 UTC
Re: [CAD_CAM_EDM_DRO] which steppers to buy?
Tony Jeffree
2001-05-28 03:06:49 UTC
Re: which steppers to buy?
Chris Stratton
2001-05-28 07:21:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: which steppers to buy?
Alan Marconett KM6VV
2001-05-28 13:53:03 UTC
Re: [CAD_CAM_EDM_DRO] which steppers to buy?
Art Fenerty
2001-05-28 14:35:12 UTC
Re: [CAD_CAM_EDM_DRO] which steppers to buy?
Chris Stratton
2001-05-28 15:34:39 UTC
Re: [CAD_CAM_EDM_DRO] which steppers to buy?
Art Fenerty
2001-05-28 15:55:10 UTC
Re: [CAD_CAM_EDM_DRO] which steppers to buy?
Art Fenerty
2001-05-28 16:02:58 UTC
Re: [CAD_CAM_EDM_DRO] which steppers to buy?
Chris Stratton
2001-05-28 17:42:45 UTC
Re: [CAD_CAM_EDM_DRO] which steppers to buy?