CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] which steppers to buy?

on 2001-05-28 17:42:45 UTC
Art, I got the rating wrong, it is only 980 hold, 500 run.
Their biggest one (bottom of page 11) weight 16 lbs and costs $40.

I can't help but wonder if there is any way these could be rewound.
I've got a disassembled little nema 23 (and odd beast that is only 24
steps/revolution) and the windings around each pole are connected in
series with the one two poles over - ie, the two phases are big long
series chains. If it were possible to cut those wires and wire each
phase up to parallel all its component poles, one might have a nice
low-inductance motor. Ie, $40 plus several hours work giving the
equivelent of a $300 motor...

But it would be tricky to do without damaging the motor.

Chris

> > www.herbach.com has some big ones of these 1125 oz in I think.
>
>
> Sorry, just checked that link. The motors I use are SS400 motors, the one at
> the link at SS25's. They say the SS25's are 4.5 lb/inch
> of torque, the SS400 is about 7inches long, has a 1/2 inch shaft are are
> heavy. You can still find them at surplus places if you look around.
>
> Good Lck,
> Art
>
>
>
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
> FAQ: http://www.ktmarketing.com/faq.html
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>


--
Christopher C. Stratton, stratton@...
Instrument Maker, Horn Player & Engineer
22 Adrian Street, Somerville, MA 02143
http://www.mdc.net/~stratton
NEW PHONE NUMBER: (617) 628-1062 home, 253-2606 MIT

Discussion Thread

jh1221@a... 2001-05-27 06:53:14 UTC which steppers to buy? RC 2001-05-27 09:12:24 UTC Re: [CAD_CAM_EDM_DRO] which steppers to buy? Tim Goldstein 2001-05-27 09:27:17 UTC RE: [CAD_CAM_EDM_DRO] which steppers to buy? Tim Goldstein 2001-05-27 09:32:21 UTC RE: [CAD_CAM_EDM_DRO] which steppers to buy? RC 2001-05-27 09:37:34 UTC Re: [CAD_CAM_EDM_DRO] which steppers to buy? marble here 2001-05-27 19:40:44 UTC RE: [CAD_CAM_EDM_DRO] which steppers to buy? Jerry Kimberlin 2001-05-27 19:48:58 UTC Re: [CAD_CAM_EDM_DRO] which steppers to buy? Chris Stratton 2001-05-27 20:18:39 UTC Re: [CAD_CAM_EDM_DRO] which steppers to buy? Tim Goldstein 2001-05-27 20:27:43 UTC RE: [CAD_CAM_EDM_DRO] which steppers to buy? Tim Goldstein 2001-05-27 20:29:57 UTC RE: [CAD_CAM_EDM_DRO] which steppers to buy? Jon Elson 2001-05-27 20:57:54 UTC Re: [CAD_CAM_EDM_DRO] which steppers to buy? Jon Elson 2001-05-27 21:00:37 UTC Re: [CAD_CAM_EDM_DRO] which steppers to buy? Hugh & Denise Currin 2001-05-27 22:53:08 UTC Re: which steppers to buy? Ian Wright 2001-05-28 01:28:49 UTC Re: [CAD_CAM_EDM_DRO] which steppers to buy? Tony Jeffree 2001-05-28 03:06:49 UTC Re: which steppers to buy? Chris Stratton 2001-05-28 07:21:07 UTC Re: [CAD_CAM_EDM_DRO] Re: which steppers to buy? Alan Marconett KM6VV 2001-05-28 13:53:03 UTC Re: [CAD_CAM_EDM_DRO] which steppers to buy? Art Fenerty 2001-05-28 14:35:12 UTC Re: [CAD_CAM_EDM_DRO] which steppers to buy? Chris Stratton 2001-05-28 15:34:39 UTC Re: [CAD_CAM_EDM_DRO] which steppers to buy? Art Fenerty 2001-05-28 15:55:10 UTC Re: [CAD_CAM_EDM_DRO] which steppers to buy? Art Fenerty 2001-05-28 16:02:58 UTC Re: [CAD_CAM_EDM_DRO] which steppers to buy? Chris Stratton 2001-05-28 17:42:45 UTC Re: [CAD_CAM_EDM_DRO] which steppers to buy?