Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
Posted by
JanRwl@A...
on 2001-07-16 10:21:24 UTC
In a message dated 16-Jul-01 12:13:56 Central Daylight Time, hugh@...
writes:
[Non-text portions of this message have been removed]
writes:
> Yes daughter, these were considered state of the art high density storageIt IS mind-bending, how things have changed in a couple of decades, isn't it!
> when your dad got into computers.
>
[Non-text portions of this message have been removed]
Discussion Thread
Alan Trest
2001-07-15 13:57:00 UTC
8" Floppy Drive Motor question
Alan Marconett KM6VV
2001-07-15 15:40:41 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
cncdxf@a...
2001-07-15 16:49:31 UTC
Re: 8" Floppy Drive Motor question
Alan Trest
2001-07-15 18:02:30 UTC
Re: 8" Floppy Drive Motor question
Henry H. Armstrong
2001-07-15 21:18:09 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
Jon Elson
2001-07-15 22:48:17 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
Jon Elson
2001-07-15 22:56:30 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
cadcamcenter@y...
2001-07-16 09:35:18 UTC
8" Floppy Drive Motor question
Hugh Prescott
2001-07-16 10:04:24 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
jguenther@v...
2001-07-16 10:18:02 UTC
RE: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
JanRwl@A...
2001-07-16 10:21:24 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
JanRwl@A...
2001-07-16 10:26:09 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
Hugh Prescott
2001-07-16 10:37:53 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
Jon Elson
2001-07-16 10:48:12 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
Alan Marconett KM6VV
2001-07-16 12:28:08 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
JanRwl@A...
2001-07-16 17:57:21 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
JanRwl@A...
2001-07-16 18:25:04 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
Jon Elson
2001-07-16 22:48:43 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
Alan Marconett KM6VV
2001-07-17 12:55:05 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question