CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question

Posted by Jon Elson
on 2001-07-16 22:48:43 UTC
Alan Marconett KM6VV wrote:

> Hi Jon,
>
> Yes! Something like that WOULD be a good find. I mostly saw Shugarts,
> don't remember any board like that (it's been a while). The +24v was
> needed for the stepper drive, and there is usually a "drive chip" on the
> board, and/or driven by the LSI chip. Who made the drives you saw?

These were all Japanese makes. The motors were mostly Sanyo, I think.
The drives were Teac, Toshiba, etc.

One 8" motor was modified and spins a huge EBM impeller that cools my
ancient VAX computer quietly. A 5" motor was modified with a crank
and it is the gasoline pump in my lawn tractor.

Jon

Discussion Thread

Alan Trest 2001-07-15 13:57:00 UTC 8" Floppy Drive Motor question Alan Marconett KM6VV 2001-07-15 15:40:41 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question cncdxf@a... 2001-07-15 16:49:31 UTC Re: 8" Floppy Drive Motor question Alan Trest 2001-07-15 18:02:30 UTC Re: 8" Floppy Drive Motor question Henry H. Armstrong 2001-07-15 21:18:09 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question Jon Elson 2001-07-15 22:48:17 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question Jon Elson 2001-07-15 22:56:30 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question cadcamcenter@y... 2001-07-16 09:35:18 UTC 8" Floppy Drive Motor question Hugh Prescott 2001-07-16 10:04:24 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question jguenther@v... 2001-07-16 10:18:02 UTC RE: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question JanRwl@A... 2001-07-16 10:21:24 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question JanRwl@A... 2001-07-16 10:26:09 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question Hugh Prescott 2001-07-16 10:37:53 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question Jon Elson 2001-07-16 10:48:12 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question Alan Marconett KM6VV 2001-07-16 12:28:08 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question JanRwl@A... 2001-07-16 17:57:21 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question JanRwl@A... 2001-07-16 18:25:04 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question Jon Elson 2001-07-16 22:48:43 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question Alan Marconett KM6VV 2001-07-17 12:55:05 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question