Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
Posted by
Jon Elson
on 2001-07-15 22:56:30 UTC
Alan Marconett KM6VV wrote:
have modular motor/controllers. These usually had 3 wires, supplying a
ground, +12 V and a run signal to the motor control chip. You'll know
you have one of these when you see a small circuit board attached to the
motor with one or several chips on it, and very few wires going to the
rest of the drive circuitry. I have used these motors in several projects.
Jon
> Hi Alan,If you look caefully, you can sometimes find both 5.25 and 8" drives that
>
> I believe they were 3-phase motors, I have not been able to drive them
> (didn't try too recently), you can use the LSI or discrete drivers on
> the drive's PCB. I had/have the Shugart drives! Actually, I doubt if
> you'd find them useable for anything else. Much better to get surplus
> NEMA #23's.
have modular motor/controllers. These usually had 3 wires, supplying a
ground, +12 V and a run signal to the motor control chip. You'll know
you have one of these when you see a small circuit board attached to the
motor with one or several chips on it, and very few wires going to the
rest of the drive circuitry. I have used these motors in several projects.
Jon
Discussion Thread
Alan Trest
2001-07-15 13:57:00 UTC
8" Floppy Drive Motor question
Alan Marconett KM6VV
2001-07-15 15:40:41 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
cncdxf@a...
2001-07-15 16:49:31 UTC
Re: 8" Floppy Drive Motor question
Alan Trest
2001-07-15 18:02:30 UTC
Re: 8" Floppy Drive Motor question
Henry H. Armstrong
2001-07-15 21:18:09 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
Jon Elson
2001-07-15 22:48:17 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
Jon Elson
2001-07-15 22:56:30 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
cadcamcenter@y...
2001-07-16 09:35:18 UTC
8" Floppy Drive Motor question
Hugh Prescott
2001-07-16 10:04:24 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
jguenther@v...
2001-07-16 10:18:02 UTC
RE: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
JanRwl@A...
2001-07-16 10:21:24 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
JanRwl@A...
2001-07-16 10:26:09 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
Hugh Prescott
2001-07-16 10:37:53 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
Jon Elson
2001-07-16 10:48:12 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
Alan Marconett KM6VV
2001-07-16 12:28:08 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
JanRwl@A...
2001-07-16 17:57:21 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
JanRwl@A...
2001-07-16 18:25:04 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
Jon Elson
2001-07-16 22:48:43 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question
Alan Marconett KM6VV
2001-07-17 12:55:05 UTC
Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question