CAD CAM EDM DRO - Yahoo Group Archive

Re: 8" Floppy Drive Motor question

Posted by Alan Trest
on 2001-07-15 18:02:30 UTC
--- In CAD_CAM_EDM_DRO@y..., cncdxf@a... wrote:
> Hi Alan,
> Those motors will work fine for experimenting if they
> have 5 or 6 wires. They only have about 30oz of torq. They
> can also work in telescope or other small drive system.
>
> Bob
>
> Thanks for the input guys,

Sounds like they would not be much of a bargin so I'll pass on them.

Thanks,

Alan

Discussion Thread

Alan Trest 2001-07-15 13:57:00 UTC 8" Floppy Drive Motor question Alan Marconett KM6VV 2001-07-15 15:40:41 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question cncdxf@a... 2001-07-15 16:49:31 UTC Re: 8" Floppy Drive Motor question Alan Trest 2001-07-15 18:02:30 UTC Re: 8" Floppy Drive Motor question Henry H. Armstrong 2001-07-15 21:18:09 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question Jon Elson 2001-07-15 22:48:17 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question Jon Elson 2001-07-15 22:56:30 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question cadcamcenter@y... 2001-07-16 09:35:18 UTC 8" Floppy Drive Motor question Hugh Prescott 2001-07-16 10:04:24 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question jguenther@v... 2001-07-16 10:18:02 UTC RE: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question JanRwl@A... 2001-07-16 10:21:24 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question JanRwl@A... 2001-07-16 10:26:09 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question Hugh Prescott 2001-07-16 10:37:53 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question Jon Elson 2001-07-16 10:48:12 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question Alan Marconett KM6VV 2001-07-16 12:28:08 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question JanRwl@A... 2001-07-16 17:57:21 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question JanRwl@A... 2001-07-16 18:25:04 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question Jon Elson 2001-07-16 22:48:43 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question Alan Marconett KM6VV 2001-07-17 12:55:05 UTC Re: [CAD_CAM_EDM_DRO] 8" Floppy Drive Motor question