CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Use Router for metal work

on 2001-10-09 12:48:41 UTC
WD-40 will ignite, but that is probably due to the propellant( if used
from a spray can). Probably propane. I discovered that a few years
back, trying to quiet some noisy bearings on my shop-vac.It was pretty
exciting for a few seconds!. I use WD-40 (from a spray can) for engine
starting fluid rather than ether.
It does help keep aluminum from attaching itself to my carbide cutters
when porting aluminum heads. If you keep an old candle around the shop
that works also. Just touch the candle to the hot cutter . Carey

Ethan wrote:I think you'd have real trouble trying to get WD-40 to
ignite. It's a large
part water. I've sprayed it on red hot steel and all it did was smoke.

Ethan

Discussion Thread

Niyom Racharin 2001-10-08 23:43:59 UTC Use Router for metal work Doug Fortune 2001-10-09 00:36:31 UTC Re: [CAD_CAM_EDM_DRO] Use Router for metal work Eric Keller 2001-10-09 04:53:39 UTC Re: [CAD_CAM_EDM_DRO] Use Router for metal work Les Newell 2001-10-09 05:02:37 UTC Re: [CAD_CAM_EDM_DRO] Use Router for metal work Jon Elson 2001-10-09 11:01:29 UTC Re: [CAD_CAM_EDM_DRO] Use Router for metal work Brian Walsh 2001-10-09 11:56:39 UTC Re: [CAD_CAM_EDM_DRO] Use Router for metal work Ethan Vos 2001-10-09 12:08:33 UTC RE: [CAD_CAM_EDM_DRO] Use Router for metal work Tim 2001-10-09 12:29:32 UTC RE: [CAD_CAM_EDM_DRO] Use Router for metal work Ethan Vos 2001-10-09 12:33:41 UTC RE: [CAD_CAM_EDM_DRO] Use Router for metal work Carey L. Culpepper 2001-10-09 12:48:41 UTC Re: [CAD_CAM_EDM_DRO] Use Router for metal work Dan Mauch 2001-10-09 13:21:47 UTC RE: [CAD_CAM_EDM_DRO] Use Router for metal work William Scalione 2001-10-09 15:11:38 UTC Re: [CAD_CAM_EDM_DRO] Use Router for metal work Ron Yost 2001-10-09 15:17:50 UTC Re: [CAD_CAM_EDM_DRO] Use Router for metal work Jerry Kimberlin 2001-10-09 19:52:27 UTC Re: [CAD_CAM_EDM_DRO] Use Router for metal work Brian Walsh 2001-10-09 20:55:13 UTC Re: [CAD_CAM_EDM_DRO] Use Router for metal work David Goodfellow 2001-10-09 21:02:37 UTC Re: [CAD_CAM_EDM_DRO] Use Router for metal work Tim Goldstein 2001-10-09 21:08:16 UTC RE: [CAD_CAM_EDM_DRO] WD-40, was:Use Router for metal work Brian Walsh 2001-10-09 21:14:06 UTC Re: [CAD_CAM_EDM_DRO] Use Router for metal work Jerry Kimberlin 2001-10-09 21:14:48 UTC Re: [CAD_CAM_EDM_DRO] WD-40, was:Use Router for metal work Jerry Kimberlin 2001-10-09 21:17:53 UTC Re: [CAD_CAM_EDM_DRO] Use Router for metal work Tim Goldstein 2001-10-09 21:32:39 UTC RE: [CAD_CAM_EDM_DRO] WD-40, was:Use Router for metal work M. SHABBIR MOGHUL 2001-10-09 21:34:20 UTC Re: [CAD_CAM_EDM_DRO] Use Router for metal work Brian Walsh 2001-10-09 21:36:12 UTC Re: [CAD_CAM_EDM_DRO] Use Router for metal work Jerry Kimberlin 2001-10-09 21:55:01 UTC Re: [CAD_CAM_EDM_DRO] WD-40, was:Use Router for metal work Carol & Jerry Jankura 2001-10-10 05:39:11 UTC RE: [CAD_CAM_EDM_DRO] Use Router for metal work Smoke 2001-10-10 06:29:28 UTC Re: [CAD_CAM_EDM_DRO] Use Router for metal work johnhe 2001-10-10 07:32:23 UTC Re: [CAD_CAM_EDM_DRO] Use Router for metal work