CAD CAM EDM DRO - Yahoo Group Archive

Re: Gecko question

Posted by aspaguy
on 2002-01-31 22:30:46 UTC
Marris or others,
Thanks Mariss for taking the time to answer the post, I would have
understood if you had waited for someone else, as we are all anxiosly
awaiting your new toy. I guess this should have answered my question,
but, I have to ask, are the rev1 units not 10 microstep? I knew they
didn't come with support or warranty. I guess what I'm asking is what
were the improvements with the rev 4 and how will they apply to a
plasma table
Thanks,
Dale

PS Again, no offense taken if Mariss lets others field this
question. thanks
Mariss.
--- In CAD_CAM_EDM_DRO@y..., "mariss92705"
<mariss92705@y...> wrote:
> Dale,
>
> Good evening! There really is no G201A. All the 10 microstep units
> are called G201. They are the latest version (Rev-4) so they have
> current reduction, etc. These are supported and warranteed.
>
> The "discounted" versions are new/unused units from the original
> production run (Rev-1) and are conspicuous by their total absence
of
> a cover. They have no support or warranty.
>
> Mariss
>
>
>
> --- In CAD_CAM_EDM_DRO@y..., "aspaguy" <spaguy@l...> wrote:
> > Is there a big difference between the g201 and the g201a. I
> > understand they may run cooler as a 201a bcause of idle current
> > reduction. is the difference in heat easily handled with a good
> heat
> > exchanger? I have been reluctant to purchase the 201 because of
> these
> > questions. I know some times it's cheaper to do it right the
first
> > time, but for a plasma table running steppers at about 3.5 amps
is
> > there any advantage to the 201a
> >
> > Also, Camtronics sight lists geckos for sale, but does not
specify
> if
> > they are the discontinued or the updated versions. I suspect
they
> > are the updates. Can anyone confirm this
> > Thanks
> > Dale

Discussion Thread

Tom Eldredge 2001-03-27 07:33:21 UTC Re: [CAD_CAM_EDM_DRO] Gecko question mariss92705@y... 2001-03-27 11:21:00 UTC Re: Gecko question mariss92705@y... 2001-03-27 12:23:49 UTC Re: Gecko question mariss92705@y... 2001-03-27 20:53:51 UTC Re: Gecko question Tom Eldredge 2001-03-28 07:33:21 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko question pkranger63@y... 2001-11-18 15:20:58 UTC Gecko question shymu@b... 2001-11-18 17:36:52 UTC Re: Gecko question Alan Marconett KM6VV 2001-11-18 18:18:56 UTC Re: [CAD_CAM_EDM_DRO] Gecko question Jon Elson 2001-11-18 21:20:30 UTC Re: [CAD_CAM_EDM_DRO] Gecko question Alan Marconett KM6VV 2001-11-19 10:35:30 UTC Re: [CAD_CAM_EDM_DRO] Gecko question Al Schoepp 2001-11-20 11:04:22 UTC Re: [CAD_CAM_EDM_DRO] Gecko question aspaguy 2002-01-31 19:42:38 UTC Gecko question seanc62 2002-01-31 20:28:00 UTC Re: Gecko question mariss92705 2002-01-31 20:38:21 UTC Re: Gecko question aspaguy 2002-01-31 22:30:46 UTC Re: Gecko question mariss92705 2002-01-31 22:37:49 UTC Re: Gecko question Dan Mauch 2002-02-01 07:17:11 UTC RE: [CAD_CAM_EDM_DRO] Gecko question aspaguy 2002-02-01 17:52:56 UTC Thanks Mariss Re: Gecko question