Re: [CAD_CAM_EDM_DRO] G201 Question for Mariss
Posted by
RC
on 2002-04-06 03:24:04 UTC
What was you going use the "disable" mode for? If it's for an emergency
type panic button, then connecting all make sense, how else would one stop
motion on all three quickly? I though about using two configurations, one
for a "Z" drive only, to free up that drive to make tool changes, and the
other as all three at once for an emergency stop.
Russ
type panic button, then connecting all make sense, how else would one stop
motion on all three quickly? I though about using two configurations, one
for a "Z" drive only, to free up that drive to make tool changes, and the
other as all three at once for an emergency stop.
Russ
----- Original Message -----
From: rsgoldner <rgoldner@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Friday, April 05, 2002 4:38 PM
Subject: [CAD_CAM_EDM_DRO] G201 Question for Mariss
> I have three G201s. Can I connect all three aux gnd pins (pin 12) to
> one side of a switch and all three disable pins to the other side of
> a switch? The idea is to disable all three motors with one switch.
> Is aux gnd the same as the power supply gnd and could I just connect
> all the disable pins to the PS gnd through the switch instead?
>
> Thanks!
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this as a
sister site to the CCED group, as many of the same memembers are there, for
OT subjects, that are not allowed on the CCED list.
>
>
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
Discussion Thread
rsgoldner
2002-04-05 16:38:46 UTC
G201 Question for Mariss
mariss92705
2002-04-05 17:11:47 UTC
Re: G201 Question for Mariss
Raymond Heckert
2002-04-05 20:25:45 UTC
Re: [CAD_CAM_EDM_DRO] G201 Question for Mariss
rsgoldner
2002-04-06 03:08:34 UTC
Re: G201 Question for Mariss
RC
2002-04-06 03:24:04 UTC
Re: [CAD_CAM_EDM_DRO] G201 Question for Mariss
rsgoldner
2002-04-06 06:37:40 UTC
Re: G201 Question for Mariss
RC
2002-04-06 06:59:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: G201 Question for Mariss
batwings@i...
2002-04-06 14:23:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: G201 Question for Mariss
n4onl
2002-04-15 19:52:46 UTC
G201 Question for Mariss
mariss92705
2002-04-15 21:33:16 UTC
Re: G201 Question for Mariss
n4onl
2002-04-16 20:39:24 UTC
Re: G201 Question for Mariss
n4onl
2002-04-17 04:50:18 UTC
Re: G201 Question for Mariss
cadcamcenter
2002-04-17 05:12:17 UTC
Re: G201 Question for Mariss
JanRwl@A...
2002-04-17 20:56:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: G201 Question for Mariss
mariss92705
2002-04-17 22:29:27 UTC
Re: G201 Question for Mariss