Re: [CAD_CAM_EDM_DRO] Re: G201 Question for Mariss

Sounds like a plan, let me know how it goes, because I plan on doing about
the same thing with my Gecko's .....

Russ

----- Original Message -----
From: rsgoldner <rgoldner@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Saturday, April 06, 2002 6:37 AM
Subject: [CAD_CAM_EDM_DRO] Re: G201 Question for Mariss


> I want to disable them to allow me to use the mill manually. My
> motors have dual shafts and I installed the original hand wheels on
> the rear shafts. Even if the drives are powered down the motors
> generate enough back EMF to make it hard to turn them. I am assuming
> that the disable state has the motor coils in an open circuit.
>
> --- In CAD_CAM_EDM_DRO@y..., "RC" <asdf@c...> wrote:
> > What was you going use the "disable" mode for? If it's for an
> emergency
> > type panic button, then connecting all make sense, how else would
> one stop
> > motion on all three quickly? I though about using two
> configurations, one
> > for a "Z" drive only, to free up that drive to make tool changes,
> and the
> > other as all three at once for an emergency stop.
> >
> > Russ
> > ----- Original Message -----
> > From: rsgoldner <rgoldner@i...>
> > To: <CAD_CAM_EDM_DRO@y...>
> > Sent: Friday, April 05, 2002 4:38 PM
> > Subject: [CAD_CAM_EDM_DRO] G201 Question for Mariss
> >
> >
> > > I have three G201s. Can I connect all three aux gnd pins (pin
> 12) to
> > > one side of a switch and all three disable pins to the other
> side of
> > > a switch? The idea is to disable all three motors with one
> switch.
> > > Is aux gnd the same as the power supply gnd and could I just
> connect
> > > all the disable pins to the PS gnd through the switch instead?
> > >
> > > Thanks!
> > >
> > >
> > > Addresses:
> > > FAQ: http://www.ktmarketing.com/faq.html
> > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > >
> > > OFF Topic POSTS: General Machining
> > > If you wish to post on unlimited OT subjects goto:
> > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> reach it if
> > you have trouble.
> > > http://www.metalworking.com/news_servers.html
> > >
> > > http://groups.yahoo.com/group/jobshophomeshop I consider this
> as a
> > sister site to the CCED group, as many of the same memembers are
> there, for
> > OT subjects, that are not allowed on the CCED list.
> > >
> > >
> > >
> > > Post messages: CAD_CAM_EDM_DRO@y...
> > > Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> > > List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> > > Moderator: jmelson@a... timg@k... [Moderator]
> > > URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > > bill,
> > > List Mom
> > > List Owner
> > >
> > >
> > >
> > > Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/
> > >
> > >
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this as a
sister site to the CCED group, as many of the same memembers are there, for
OT subjects, that are not allowed on the CCED list.
>
>
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>