Re: G201 Question for Mariss
Posted by
mariss92705
on 2002-04-15 21:33:16 UTC
Mike,
Best way to do that is:
(1) Clip the opto out by snipping all 8 leads right at the plastic
package. You won't get the opto out without destroying it anyway
unless you have a re-work station.
(2) Unsolder each lead from the bottom while pulling the lead out
from the top with tweezers.
(3) Chase each hole with a .031" drill bit. It's best to have the bit
in a miniature chuck you can twrill thith your thumb and forefinger.
(4) Use compressed air to blow any solder chips off of the drive.
(5) Use a Mill-Max Series 315..01 socket (Digi Key ED7864-ND). These
come in lengths of 64 pins. Use an Exacto knife to cut it in lenghts
of 4 pins. If you plan to get the multiplier from us (G901), let me
know and I will throw in the sockets.
(6) Solder the sockets in with .025" dia. rosin core solder.
Mariss
Best way to do that is:
(1) Clip the opto out by snipping all 8 leads right at the plastic
package. You won't get the opto out without destroying it anyway
unless you have a re-work station.
(2) Unsolder each lead from the bottom while pulling the lead out
from the top with tweezers.
(3) Chase each hole with a .031" drill bit. It's best to have the bit
in a miniature chuck you can twrill thith your thumb and forefinger.
(4) Use compressed air to blow any solder chips off of the drive.
(5) Use a Mill-Max Series 315..01 socket (Digi Key ED7864-ND). These
come in lengths of 64 pins. Use an Exacto knife to cut it in lenghts
of 4 pins. If you plan to get the multiplier from us (G901), let me
know and I will throw in the sockets.
(6) Solder the sockets in with .025" dia. rosin core solder.
Mariss
--- In CAD_CAM_EDM_DRO@y..., "n4onl" <umrk@b...> wrote:
>
> Hi,
> I have 3 of the original 201's and was wondering if they would
> support the multiplier board if the optocoupler was desoldered and
> replaced with a socket. I realize these are multilayer boards and
> require extra care in desoldering.
>
> Thanks
> mike
Discussion Thread
rsgoldner
2002-04-05 16:38:46 UTC
G201 Question for Mariss
mariss92705
2002-04-05 17:11:47 UTC
Re: G201 Question for Mariss
Raymond Heckert
2002-04-05 20:25:45 UTC
Re: [CAD_CAM_EDM_DRO] G201 Question for Mariss
rsgoldner
2002-04-06 03:08:34 UTC
Re: G201 Question for Mariss
RC
2002-04-06 03:24:04 UTC
Re: [CAD_CAM_EDM_DRO] G201 Question for Mariss
rsgoldner
2002-04-06 06:37:40 UTC
Re: G201 Question for Mariss
RC
2002-04-06 06:59:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: G201 Question for Mariss
batwings@i...
2002-04-06 14:23:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: G201 Question for Mariss
n4onl
2002-04-15 19:52:46 UTC
G201 Question for Mariss
mariss92705
2002-04-15 21:33:16 UTC
Re: G201 Question for Mariss
n4onl
2002-04-16 20:39:24 UTC
Re: G201 Question for Mariss
n4onl
2002-04-17 04:50:18 UTC
Re: G201 Question for Mariss
cadcamcenter
2002-04-17 05:12:17 UTC
Re: G201 Question for Mariss
JanRwl@A...
2002-04-17 20:56:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: G201 Question for Mariss
mariss92705
2002-04-17 22:29:27 UTC
Re: G201 Question for Mariss