Re: [CAD_CAM_EDM_DRO] Using a CNC Mill to tap holes?
Posted by
bjammin@i...
on 2002-05-13 08:16:58 UTC
At 05:26 PM 5/13/02 +1000, you wrote:
software. Spindle is driven by stepper, carriage 'geared' to it. I use a
single point, but a tap would serve as well. It would take a slight mod on
the method of returning the tap but that's a snap to rig.
Regards, Hoyt
Anti-virus request: Please do not add this email addy to address books
Belfab CNC - http://www.freeyellow.com/members/belfab/belfab.html
US Best MC - http://www.freeyellow.com/members/batwings/best.html
Camping/Caving - http://www.freeyellow.com/members/batwings/caving.html
Jo-moma always tella u tru, so listen jo-moma whatever u du
>Hi,In principle it is exactly the same as the way I cut threads with my
>
>Is it practical to tap holes using a CNC Mill (Taig) by driving the spindle
>with a stepper motor and holding a standard tap in a collet?
software. Spindle is driven by stepper, carriage 'geared' to it. I use a
single point, but a tap would serve as well. It would take a slight mod on
the method of returning the tap but that's a snap to rig.
Regards, Hoyt
Anti-virus request: Please do not add this email addy to address books
Belfab CNC - http://www.freeyellow.com/members/belfab/belfab.html
US Best MC - http://www.freeyellow.com/members/batwings/best.html
Camping/Caving - http://www.freeyellow.com/members/batwings/caving.html
Jo-moma always tella u tru, so listen jo-moma whatever u du
Discussion Thread
Andrew Werby
2002-05-12 19:54:34 UTC
Re: [CAD_CAM_EDM_DRO] Digest Number 2309
thosmurray
2002-05-12 23:06:23 UTC
Anti-backlash on Taig mill was:Re: Digest Number 2309
Peter Homann
2002-05-13 00:27:22 UTC
Using a CNC Mill to tap holes?
Steve Blackmore
2002-05-13 00:54:37 UTC
Re: [CAD_CAM_EDM_DRO] Anti-backlash on Taig mill was:Re: Digest Number 2309
Marcus & Eva
2002-05-13 08:11:06 UTC
Re: [CAD_CAM_EDM_DRO] Using a CNC Mill to tap holes?
bjammin@i...
2002-05-13 08:16:58 UTC
Re: [CAD_CAM_EDM_DRO] Using a CNC Mill to tap holes?
Elliot Burke
2002-05-13 10:50:22 UTC
re:Re: Anti-backlash on Taig mill was:Re: Digest Number 2309
Steve Blackmore
2002-05-13 12:28:37 UTC
Re: [CAD_CAM_EDM_DRO] re:Re: Anti-backlash on Taig mill was:Re: Digest Number 2309
JanRwl@A...
2002-05-13 14:45:59 UTC
Re: [CAD_CAM_EDM_DRO] Using a CNC Mill to tap holes?
Jon Elson
2002-05-13 22:20:31 UTC
Re: [CAD_CAM_EDM_DRO] Using a CNC Mill to tap holes?
bjammin@i...
2002-05-14 03:48:59 UTC
Anti-backlash on Taig mill
Steve Blackmore
2002-05-14 05:24:39 UTC
Re: [CAD_CAM_EDM_DRO] Anti-backlash on Taig mill
tonyjeffree
2002-05-14 11:26:45 UTC
Re: Anti-backlash on Taig mill
Andrew Werby
2002-05-14 11:49:01 UTC
Anti-backlash on Taig mill