CAD CAM EDM DRO - Yahoo Group Archive

Anti-backlash on Taig mill

Posted by bjammin@i...
on 2002-05-14 03:48:59 UTC
Even if the screw is tensioned, that has no effect on the lash at the nut,
none!


At 10:51 AM 5/13/02 -0700, you wrote:
>Steve Blackmore writes:
>>The ends of the screws have a ballrace which is tensioned by the
>>endnut - this removes the backlash - isn't this good enough for you?
>
>I have a Taig mill, it has 1/2-20 leadscrews and a brass(?) nut. The screw
>is supported at the motor end, not at the end opposite the motor.
>
>Where are the tensioning screws you mention and the ballrace?
>
>Elliot Burke
>
>
>Addresses:
>FAQ: http://www.ktmarketing.com/faq.html
>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
>OFF Topic POSTS: General Machining
>If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
>http://www.metalworking.com/news_servers.html
>
>http://groups.yahoo.com/group/jobshophomeshop I consider this as a
sister site to the CCED group, as many of the same members are there, for
OT subjects, that are not allowed on the CCED list.
>
>
>
>Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
>Moderator: jmelson@... timg@... [Moderator]
>URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>bill,
>List Mom
>List Owner
>
>
>
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>
>

Regards, Hoyt


Anti-virus request: Please do not add this email addy to address books
Belfab CNC - http://www.freeyellow.com/members/belfab/belfab.html
US Best MC - http://www.freeyellow.com/members/batwings/best.html
Camping/Caving - http://www.freeyellow.com/members/batwings/caving.html
Jo-moma always tella u tru, so listen jo-moma whatever u du

Discussion Thread

Andrew Werby 2002-05-12 19:54:34 UTC Re: [CAD_CAM_EDM_DRO] Digest Number 2309 thosmurray 2002-05-12 23:06:23 UTC Anti-backlash on Taig mill was:Re: Digest Number 2309 Peter Homann 2002-05-13 00:27:22 UTC Using a CNC Mill to tap holes? Steve Blackmore 2002-05-13 00:54:37 UTC Re: [CAD_CAM_EDM_DRO] Anti-backlash on Taig mill was:Re: Digest Number 2309 Marcus & Eva 2002-05-13 08:11:06 UTC Re: [CAD_CAM_EDM_DRO] Using a CNC Mill to tap holes? bjammin@i... 2002-05-13 08:16:58 UTC Re: [CAD_CAM_EDM_DRO] Using a CNC Mill to tap holes? Elliot Burke 2002-05-13 10:50:22 UTC re:Re: Anti-backlash on Taig mill was:Re: Digest Number 2309 Steve Blackmore 2002-05-13 12:28:37 UTC Re: [CAD_CAM_EDM_DRO] re:Re: Anti-backlash on Taig mill was:Re: Digest Number 2309 JanRwl@A... 2002-05-13 14:45:59 UTC Re: [CAD_CAM_EDM_DRO] Using a CNC Mill to tap holes? Jon Elson 2002-05-13 22:20:31 UTC Re: [CAD_CAM_EDM_DRO] Using a CNC Mill to tap holes? bjammin@i... 2002-05-14 03:48:59 UTC Anti-backlash on Taig mill Steve Blackmore 2002-05-14 05:24:39 UTC Re: [CAD_CAM_EDM_DRO] Anti-backlash on Taig mill tonyjeffree 2002-05-14 11:26:45 UTC Re: Anti-backlash on Taig mill Andrew Werby 2002-05-14 11:49:01 UTC Anti-backlash on Taig mill