Re: small 3-axis micro stepper
Posted by
ballendo
on 2002-09-17 04:08:32 UTC
Jon,
On my Sherline I get 40-60IPM with a 34v, L297-298 (2A) drive (half
step modified)
Ballendo
On my Sherline I get 40-60IPM with a 34v, L297-298 (2A) drive (half
step modified)
Ballendo
--- In CAD_CAM_EDM_DRO@y..., Jon Elson <elson@p...> wrote:
> Tim Goldstein wrote:
>
> > No offense to Mariss and Gecko as I use his products and think
they are
> > great.
> > <rant>
> > But, for what ever reason the general thought has become that
everything
> > need to run at 20 - 25x rated voltage and have a zillion amps.
>
> Where this all come from is the Sherline, with that insane 20 TPI
leadscrew.
> This requires the stepper motors to run very fast (for standard 2-
phase steppers).
> To get 25 IPM, that requires 25 x 20 = 500 RPM with a direct-drive
motor.
> 500 RPM x 200 steps/rev = 100,000 steps/min or 1667 steps/sec.
While not
> outrageous, this is getting into the higher performance range of
many motors.
> To get any torque at these speeds, your power supply needs to be
many
> times the straight IR drop in the windings.
>
> > I can
> > assure you that there are lots of machines happily running on
Camtronics
> > controllers that max out at 36 volts and L297/298 setups. Believe
it or
> > not I had my Shoptask happily running on 3.? V motors with a 24
volt
> > supply and was getting 90 ipm rapids.
>
> Well, that's quite respectable! But, I've never seen a Sherline do
that!
>
> Jon
Discussion Thread
bsptrades
2002-09-07 16:13:25 UTC
small 3-axis micro stepper
acplt2000
2002-09-12 05:45:00 UTC
Re: small 3-axis micro stepper
J
2002-09-16 16:04:24 UTC
Re: [CAD_CAM_EDM_DRO] small 3-axis micro stepper
Robert Campbell
2002-09-16 16:49:20 UTC
Re: [CAD_CAM_EDM_DRO] small 3-axis micro stepper
J
2002-09-16 19:22:38 UTC
Re: [CAD_CAM_EDM_DRO] small 3-axis micro stepper
Dan Statman
2002-09-16 19:35:09 UTC
Re: [CAD_CAM_EDM_DRO] small 3-axis micro stepper
Brian Punkar
2002-09-16 21:22:40 UTC
Re: small 3-axis micro stepper
Steve Stallings
2002-09-16 21:31:02 UTC
Re: small 3-axis micro stepper
Tim Goldstein
2002-09-16 22:21:18 UTC
RE: [CAD_CAM_EDM_DRO] small 3-axis micro stepper
Tim Goldstein
2002-09-16 22:25:07 UTC
RE: [CAD_CAM_EDM_DRO] small 3-axis micro stepper
Matt Shaver
2002-09-16 22:44:06 UTC
Re: [CAD_CAM_EDM_DRO] small 3-axis micro stepper
Jon Elson
2002-09-16 22:50:55 UTC
Re: [CAD_CAM_EDM_DRO] small 3-axis micro stepper
Doug Fortune
2002-09-16 22:55:56 UTC
Re: [CAD_CAM_EDM_DRO] small 3-axis micro stepper
Dan Statman
2002-09-17 03:25:09 UTC
Re: [CAD_CAM_EDM_DRO] small 3-axis micro stepper
ballendo
2002-09-17 04:04:27 UTC
Re: small 3-axis micro stepper
ballendo
2002-09-17 04:08:32 UTC
Re: small 3-axis micro stepper
John
2002-09-17 04:22:38 UTC
RE: [CAD_CAM_EDM_DRO] Re: small 3-axis micro stepper
bjammin@i...
2002-09-17 04:40:36 UTC
RE: [CAD_CAM_EDM_DRO] small 3-axis micro stepper
caudlet
2002-09-17 06:02:14 UTC
Re: small 3-axis micro stepper(Tim's Rant)
Carol & Jerry Jankura
2002-09-17 06:17:49 UTC
RE: [CAD_CAM_EDM_DRO] small 3-axis micro stepper
Dan Mauch
2002-09-17 06:17:54 UTC
RE: [CAD_CAM_EDM_DRO] small 3-axis micro stepper
William Scalione
2002-09-17 06:56:36 UTC
Re: [CAD_CAM_EDM_DRO] small 3-axis micro stepper
Dan Mauch
2002-09-17 07:12:08 UTC
RE: [CAD_CAM_EDM_DRO] small 3-axis micro stepper
J
2002-09-17 07:12:27 UTC
RE: [CAD_CAM_EDM_DRO] small 3-axis micro stepper
Michael Holm
2002-09-17 07:23:43 UTC
Re: [CAD_CAM_EDM_DRO] small 3-axis micro stepper
Jon Elson
2002-09-17 10:10:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: small 3-axis micro stepper
Tim Goldstein
2002-09-17 10:42:21 UTC
Re: [CAD_CAM_EDM_DRO] small 3-axis micro stepper
ballendo
2002-10-01 20:33:41 UTC
Re: small 3-axis micro stepper