Re: [CAD_CAM_EDM_DRO] SeriesII Quill Zaxis CNC addon ideas: Like Jon E's?
Posted by
Tim Goldstein
on 2002-11-21 16:51:06 UTC
Marv,
The only downside of doing it with an acme screw is the wear. Carrying that
much weight and moving it all the time will likely yield an inconsistent
pitch in a relatively short time. Besides, on my machine it was already
equipped with the ground screws from the factory.
Tim
[Denver, CO]
Sherline products at Deep Discount (now Mach1 CNC controller too)
www.KTMarketing.com/Sherline
The only downside of doing it with an acme screw is the wear. Carrying that
much weight and moving it all the time will likely yield an inconsistent
pitch in a relatively short time. Besides, on my machine it was already
equipped with the ground screws from the factory.
Tim
[Denver, CO]
Sherline products at Deep Discount (now Mach1 CNC controller too)
www.KTMarketing.com/Sherline
----- Original Message -----
> Tim
> If you size your motor properly, with the right gearing, is it
really
> necessary to convert the knee to ballscrew? It seems to me, with that much
> weight on the screw, the original acme screw would have virtually no
> backlash. Gravity would take care of it. If we could figure out how to put
> the same amount of tension on the x and y axes, we would probably never
have
> to concern ourselves with their backlash. Aren't we doing almost the same
> thing with pre-loaded nuts?
>
> Marv Frankel
> Los Angeles
Discussion Thread
Lee Studley
2002-11-21 12:44:23 UTC
SeriesII Quill Zaxis CNC addon ideas: Like Jon E's?
Tim Goldstein
2002-11-21 13:48:40 UTC
Re: [CAD_CAM_EDM_DRO] SeriesII Quill Zaxis CNC addon ideas: Like Jon E's?
Marv Frankel
2002-11-21 14:12:21 UTC
Re: [CAD_CAM_EDM_DRO] SeriesII Quill Zaxis CNC addon ideas: Like Jon E's?
Lee Studley
2002-11-21 14:14:48 UTC
Re: SeriesII Quill Zaxis CNC addon ideas: Like Jon E's?
Lee Studley
2002-11-21 14:17:41 UTC
Re: SeriesII Quill Zaxis CNC addon ideas: Like Jon E's?
Tim Goldstein
2002-11-21 16:51:06 UTC
Re: [CAD_CAM_EDM_DRO] SeriesII Quill Zaxis CNC addon ideas: Like Jon E's?
Jon Elson
2002-11-21 22:58:34 UTC
Re: [CAD_CAM_EDM_DRO] SeriesII Quill Zaxis CNC addon ideas: Like Jon E's?
Marv Frankel
2002-11-22 00:45:05 UTC
Re: [CAD_CAM_EDM_DRO] SeriesII Quill Zaxis CNC addon ideas: Like Jon E's?
Dan Mauch
2002-11-22 06:57:40 UTC
RE: [CAD_CAM_EDM_DRO] SeriesII Quill Zaxis CNC addon ideas: Like JonE's?
Marv Frankel
2002-11-22 07:52:02 UTC
Re: [CAD_CAM_EDM_DRO] SeriesII Quill Zaxis CNC addon ideas: Like JonE's?
vrsculptor
2002-11-22 08:22:16 UTC
Re: SeriesII Quill Zaxis CNC addon ideas: Like JonE's?
Dan Mauch
2002-11-22 08:59:45 UTC
RE: [CAD_CAM_EDM_DRO] SeriesII Quill Zaxis CNC addon ideas: LikeJonE's?
Dan Mauch
2002-11-22 09:05:27 UTC
RE: [CAD_CAM_EDM_DRO] Re: SeriesII Quill Zaxis CNC addon ideas: Like JonE's?
Jon Elson
2002-11-22 09:55:54 UTC
Re: [CAD_CAM_EDM_DRO] SeriesII Quill Zaxis CNC addon ideas: Like Jon E's?