Re: question for Mariss
Posted by
Mariss Freimanis
on 2003-03-23 13:43:49 UTC
Jan,
Shottky diode with 0.3V forward drop at 16mA. Two diodes plus opto
LED of 1.2V at 16mA equals 1.8V. 5V minus 1.8V equals 3.2V. Current
limit resistor at 3.2V divided by 0.016A equals 200 ohms.
Math seems OK to you?
Mariss
Shottky diode with 0.3V forward drop at 16mA. Two diodes plus opto
LED of 1.2V at 16mA equals 1.8V. 5V minus 1.8V equals 3.2V. Current
limit resistor at 3.2V divided by 0.016A equals 200 ohms.
Math seems OK to you?
Mariss
--- In CAD_CAM_EDM_DRO@yahoogroups.com, JanRwl@A... wrote:
> In a message dated 3/23/2003 7:41:19 AM Central Standard Time,
xyz@h...
> writes:
>
> > However Mariss mentions there may be a hardware change that makes
the issue
> > irrelevant for new models.
>
>
> Yes, but seems to po' dum' me that inserting a "bridge" rect.
before the
> input-LED will introduce a 1.2-1.4 V. DROP, so what does this do to
the
> "Valid Input" specs????????
>
> Jan Rowland
>
>
>
>
>
> [Non-text portions of this message have been removed]
Discussion Thread
ja_erickson
2003-03-22 06:41:06 UTC
question for Mariss
Hans Wedemeyer
2003-03-22 07:39:19 UTC
Re: [CAD_CAM_EDM_DRO] question for Mariss
Monte Westlund
2003-03-22 08:18:09 UTC
Re: question for Mariss
Tim Goldstein
2003-03-22 09:35:39 UTC
RE: [CAD_CAM_EDM_DRO] question for Mariss
Mariss Freimanis
2003-03-22 10:25:10 UTC
Re: question for Mariss
Hans Wedemeyer
2003-03-22 20:28:33 UTC
Re: [CAD_CAM_EDM_DRO] question for Mariss
Hans Wedemeyer
2003-03-22 20:47:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: question for Mariss
RichD
2003-03-22 21:23:53 UTC
Re: [CAD_CAM_EDM_DRO] question for Mariss
Hans Wedemeyer
2003-03-23 05:40:57 UTC
Re: [CAD_CAM_EDM_DRO] question for Mariss
JanRwl@A...
2003-03-23 12:33:44 UTC
Re: [CAD_CAM_EDM_DRO] question for Mariss
JanRwl@A...
2003-03-23 12:46:21 UTC
Re: [CAD_CAM_EDM_DRO] question for Mariss
William Scalione
2003-03-23 13:03:46 UTC
Re: [CAD_CAM_EDM_DRO] question for Mariss
William Scalione
2003-03-23 13:03:46 UTC
Re: [CAD_CAM_EDM_DRO] question for Mariss
William Scalione
2003-03-23 13:03:47 UTC
Re: [CAD_CAM_EDM_DRO] question for Mariss
William Scalione
2003-03-23 13:03:47 UTC
Re: [CAD_CAM_EDM_DRO] question for Mariss
William Scalione
2003-03-23 13:03:50 UTC
Re: [CAD_CAM_EDM_DRO] question for Mariss
William Scalione
2003-03-23 13:03:50 UTC
Re: [CAD_CAM_EDM_DRO] question for Mariss
Mariss Freimanis
2003-03-23 13:43:49 UTC
Re: question for Mariss
JanRwl@A...
2003-03-23 14:19:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: question for Mariss
Andrew Mawson
2003-03-23 14:48:30 UTC
Re: question for Mariss
Mariss Freimanis
2003-03-23 15:08:12 UTC
Re: question for Mariss
Jon Elson
2003-03-23 17:28:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: question for Mariss
Mariss Freimanis
2003-03-23 21:29:36 UTC
Re: question for Mariss
Jon Elson
2003-03-24 08:30:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: question for Mariss
Mariss Freimanis
2003-03-24 10:13:52 UTC
Re: question for Mariss
wanliker@a...
2003-03-24 18:21:27 UTC
Re: [CAD_CAM_EDM_DRO] question for Mariss
Mariss Freimanis
2003-03-24 20:52:26 UTC
Re: question for Mariss
turbulatordude
2003-03-25 05:11:54 UTC
Re: question for Mariss