CAD CAM EDM DRO - Yahoo Group Archive

Re: question for Mariss

on 2003-03-24 20:52:26 UTC
Bill,

Having read enough confusing manuals myself, what I try to do is to
employ redundancy.

1) There is the text printed on the can that some have issue with.
2) There is the manual which plainly says what to do.
3) There are graphics on the can that shows what to do.

If there is confusion on one source, I would think the other two
would outvote the ambiguous input. This to me is almost like the "how
many angels can dance on the head of a pin" debate. It's fun, it's
interesting but ultimately it's pointless.

Mariss



--- In CAD_CAM_EDM_DRO@yahoogroups.com, wanliker@a... wrote:
> In a message dated 3/23/2003 1:47:14 PM Mountain Standard Time,
> JanRwl@A... writes:
>
> > Someone may be getting ready to squawl, "OFF TOPIC", but this is
a VERY
> > valid
> > consideration, and it is GOOD to see it discussed here!
> >
>
> Very much ON TOPIC.
>
> To help see what common is, hook 2 batteries in series and bring
out three
> leads..........Which is the common?????
> It can be any one of them depending on a +3 volt, -3 volt, or a
+1.5 and a
> -1.5 volt output.
>
> Common is simply the point that the other voltages are referenced
to.
> Nothing more, nothing less.....
>
> If I stand in front of you and hold my hand out in front of me and
ask is it
> up, or down. There is no correct answer, without knowing what I am
> referencing to, the floor, or the ceiling.
>
>
> [Non-text portions of this message have been removed]

Discussion Thread

ja_erickson 2003-03-22 06:41:06 UTC question for Mariss Hans Wedemeyer 2003-03-22 07:39:19 UTC Re: [CAD_CAM_EDM_DRO] question for Mariss Monte Westlund 2003-03-22 08:18:09 UTC Re: question for Mariss Tim Goldstein 2003-03-22 09:35:39 UTC RE: [CAD_CAM_EDM_DRO] question for Mariss Mariss Freimanis 2003-03-22 10:25:10 UTC Re: question for Mariss Hans Wedemeyer 2003-03-22 20:28:33 UTC Re: [CAD_CAM_EDM_DRO] question for Mariss Hans Wedemeyer 2003-03-22 20:47:42 UTC Re: [CAD_CAM_EDM_DRO] Re: question for Mariss RichD 2003-03-22 21:23:53 UTC Re: [CAD_CAM_EDM_DRO] question for Mariss Hans Wedemeyer 2003-03-23 05:40:57 UTC Re: [CAD_CAM_EDM_DRO] question for Mariss JanRwl@A... 2003-03-23 12:33:44 UTC Re: [CAD_CAM_EDM_DRO] question for Mariss JanRwl@A... 2003-03-23 12:46:21 UTC Re: [CAD_CAM_EDM_DRO] question for Mariss William Scalione 2003-03-23 13:03:46 UTC Re: [CAD_CAM_EDM_DRO] question for Mariss William Scalione 2003-03-23 13:03:46 UTC Re: [CAD_CAM_EDM_DRO] question for Mariss William Scalione 2003-03-23 13:03:47 UTC Re: [CAD_CAM_EDM_DRO] question for Mariss William Scalione 2003-03-23 13:03:47 UTC Re: [CAD_CAM_EDM_DRO] question for Mariss William Scalione 2003-03-23 13:03:50 UTC Re: [CAD_CAM_EDM_DRO] question for Mariss William Scalione 2003-03-23 13:03:50 UTC Re: [CAD_CAM_EDM_DRO] question for Mariss Mariss Freimanis 2003-03-23 13:43:49 UTC Re: question for Mariss JanRwl@A... 2003-03-23 14:19:50 UTC Re: [CAD_CAM_EDM_DRO] Re: question for Mariss Andrew Mawson 2003-03-23 14:48:30 UTC Re: question for Mariss Mariss Freimanis 2003-03-23 15:08:12 UTC Re: question for Mariss Jon Elson 2003-03-23 17:28:59 UTC Re: [CAD_CAM_EDM_DRO] Re: question for Mariss Mariss Freimanis 2003-03-23 21:29:36 UTC Re: question for Mariss Jon Elson 2003-03-24 08:30:24 UTC Re: [CAD_CAM_EDM_DRO] Re: question for Mariss Mariss Freimanis 2003-03-24 10:13:52 UTC Re: question for Mariss wanliker@a... 2003-03-24 18:21:27 UTC Re: [CAD_CAM_EDM_DRO] question for Mariss Mariss Freimanis 2003-03-24 20:52:26 UTC Re: question for Mariss turbulatordude 2003-03-25 05:11:54 UTC Re: question for Mariss