Re: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ??
Posted by
Alan Marconett KM6VV
on 2003-06-08 19:27:48 UTC
Hi Dave, Jeff, Luis,
I do know that the Geckos have some anti resonance filters/circuitry.
And, they are running at 10 uSteps all the time (G210 adds a pulse
multiplier up front, for modes other the 1/10 step).
As mentioned, microstepping drivers can make otherwise less then smooth
step streams acceptable.
I'm not as familiar with the Allegro chips. I'm thinking of getting a
sample (Xylotex).
Alan KM6VV
turbulatordude wrote:
I do know that the Geckos have some anti resonance filters/circuitry.
And, they are running at 10 uSteps all the time (G210 adds a pulse
multiplier up front, for modes other the 1/10 step).
As mentioned, microstepping drivers can make otherwise less then smooth
step streams acceptable.
I'm not as familiar with the Allegro chips. I'm thinking of getting a
sample (Xylotex).
Alan KM6VV
turbulatordude wrote:
>
> I am not sure if this is exactly correct.
>
> if you have a small mill (sherline) and if you have small motors and
> if you are running a 30 volt power supply.....
>
> then will one work better at 2 amps and 30 volts ?
>
> yes the Gecko can do 7 amps and 70 volts, but if you are running at
> 2amps/30V does one work better than another ?
>
> Dave
Discussion Thread
luisguillermo98
2003-06-08 05:21:36 UTC
XYLOTEX VS GECKO DRIVE ??
turbulatordude
2003-06-08 06:34:31 UTC
Re: XYLOTEX VS GECKO DRIVE ??
jeffalanp
2003-06-08 10:14:16 UTC
Re: XYLOTEX VS GECKO DRIVE ??
Torsten
2003-06-08 11:23:29 UTC
Re: XYLOTEX VS GECKO DRIVE ??
turbulatordude
2003-06-08 16:48:21 UTC
Re: XYLOTEX VS GECKO DRIVE ??
jeffalanp
2003-06-08 18:06:19 UTC
Re: XYLOTEX VS GECKO DRIVE ??
Kim Lux
2003-06-08 18:34:54 UTC
Servo motor torque curves and duty cycle info
David A. Frantz
2003-06-08 19:17:34 UTC
Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info
Alan Marconett KM6VV
2003-06-08 19:27:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ??
William Scalione
2003-06-08 19:46:34 UTC
Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info
Kim Lux
2003-06-09 06:36:51 UTC
Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info
turbulatordude
2003-06-09 06:57:24 UTC
Re: XYLOTEX VS GECKO DRIVE ??
jeffalanp
2003-06-09 11:12:42 UTC
Re: XYLOTEX VS GECKO DRIVE ??
luisguillermo98
2003-06-10 17:11:01 UTC
Re: XYLOTEX VS GECKO DRIVE ??
Tim Goldstein
2003-06-10 17:35:16 UTC
RE: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ??
jeffalanp
2003-06-10 18:43:47 UTC
Re: XYLOTEX VS GECKO DRIVE ??
luisguillermo98
2003-06-10 18:55:21 UTC
Re: XYLOTEX VS GECKO DRIVE ??
jeffalanp
2003-06-10 19:41:58 UTC
Re: XYLOTEX VS GECKO DRIVE ??
turbulatordude
2003-06-10 20:30:01 UTC
Re: XYLOTEX VS GECKO DRIVE ?? why ?
William Scalione
2003-06-11 06:23:23 UTC
Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info
Kim Lux
2003-06-11 06:31:21 UTC
Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info
Ed Fanta
2003-06-11 06:36:05 UTC
Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info
Jon Elson
2003-06-11 09:54:47 UTC
Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info
luisguillermo98
2003-06-11 18:16:09 UTC
Re: XYLOTEX VS GECKO DRIVE ?? why ?
Peter Homann
2003-06-11 19:04:46 UTC
RE: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?
Mark Thomas
2003-06-11 19:06:02 UTC
RE: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?
Statman Designs, LLC
2003-06-11 19:59:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?
Mark Thomas
2003-06-11 20:20:09 UTC
RE: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?
Statman Designs, LLC
2003-06-11 21:04:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?
Jon Elson
2003-06-11 21:49:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?
Statman Designs, LLC
2003-06-12 04:22:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?
luisguillermo98
2003-06-12 19:29:31 UTC
Re: XYLOTEX VS GECKO DRIVE ?? why ?
Statman Designs, LLC
2003-06-12 22:40:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?
Mark Thomas
2003-06-23 15:45:20 UTC
RE: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?
Russ Waters
2003-06-25 04:22:04 UTC
RE: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?