Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info
Posted by
Ed Fanta
on 2003-06-11 06:36:05 UTC
William Scalione wrote:
the power supply directly to the motors to check out speeds and torque,
cost me over $500 dollars to get them repaired. Lesson learned. Ed.
>CAUTION CAUTION CAUTION I managed to kill two servo motors by hooking
> Hi Kim,
>
> It's a small Dyna-Myte 2000, and I am going with a 3 to 1 belt drive. No
> amps yet, but have tested it with the power supply connected directly to the
> motors and it seems to move at about 60 IPM with plenty of torque.
>
> Bill
the power supply directly to the motors to check out speeds and torque,
cost me over $500 dollars to get them repaired. Lesson learned. Ed.
Discussion Thread
luisguillermo98
2003-06-08 05:21:36 UTC
XYLOTEX VS GECKO DRIVE ??
turbulatordude
2003-06-08 06:34:31 UTC
Re: XYLOTEX VS GECKO DRIVE ??
jeffalanp
2003-06-08 10:14:16 UTC
Re: XYLOTEX VS GECKO DRIVE ??
Torsten
2003-06-08 11:23:29 UTC
Re: XYLOTEX VS GECKO DRIVE ??
turbulatordude
2003-06-08 16:48:21 UTC
Re: XYLOTEX VS GECKO DRIVE ??
jeffalanp
2003-06-08 18:06:19 UTC
Re: XYLOTEX VS GECKO DRIVE ??
Kim Lux
2003-06-08 18:34:54 UTC
Servo motor torque curves and duty cycle info
David A. Frantz
2003-06-08 19:17:34 UTC
Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info
Alan Marconett KM6VV
2003-06-08 19:27:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ??
William Scalione
2003-06-08 19:46:34 UTC
Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info
Kim Lux
2003-06-09 06:36:51 UTC
Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info
turbulatordude
2003-06-09 06:57:24 UTC
Re: XYLOTEX VS GECKO DRIVE ??
jeffalanp
2003-06-09 11:12:42 UTC
Re: XYLOTEX VS GECKO DRIVE ??
luisguillermo98
2003-06-10 17:11:01 UTC
Re: XYLOTEX VS GECKO DRIVE ??
Tim Goldstein
2003-06-10 17:35:16 UTC
RE: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ??
jeffalanp
2003-06-10 18:43:47 UTC
Re: XYLOTEX VS GECKO DRIVE ??
luisguillermo98
2003-06-10 18:55:21 UTC
Re: XYLOTEX VS GECKO DRIVE ??
jeffalanp
2003-06-10 19:41:58 UTC
Re: XYLOTEX VS GECKO DRIVE ??
turbulatordude
2003-06-10 20:30:01 UTC
Re: XYLOTEX VS GECKO DRIVE ?? why ?
William Scalione
2003-06-11 06:23:23 UTC
Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info
Kim Lux
2003-06-11 06:31:21 UTC
Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info
Ed Fanta
2003-06-11 06:36:05 UTC
Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info
Jon Elson
2003-06-11 09:54:47 UTC
Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info
luisguillermo98
2003-06-11 18:16:09 UTC
Re: XYLOTEX VS GECKO DRIVE ?? why ?
Peter Homann
2003-06-11 19:04:46 UTC
RE: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?
Mark Thomas
2003-06-11 19:06:02 UTC
RE: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?
Statman Designs, LLC
2003-06-11 19:59:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?
Mark Thomas
2003-06-11 20:20:09 UTC
RE: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?
Statman Designs, LLC
2003-06-11 21:04:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?
Jon Elson
2003-06-11 21:49:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?
Statman Designs, LLC
2003-06-12 04:22:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?
luisguillermo98
2003-06-12 19:29:31 UTC
Re: XYLOTEX VS GECKO DRIVE ?? why ?
Statman Designs, LLC
2003-06-12 22:40:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?
Mark Thomas
2003-06-23 15:45:20 UTC
RE: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?
Russ Waters
2003-06-25 04:22:04 UTC
RE: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?