CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?

Posted by Peter Homann
on 2003-06-11 19:04:46 UTC
Hi,

I've used the Xylotex 3 axis board on my Taig CNC Mill. I was using the
standard Taig ~200oz/in Uni-polar motors. The motors were wired to the
Xylotex board in 1/2 phase mode (1 wire to the centre tap, the other to one
of the coil ends).
I used a 24VDC linear power supply to power the steppers.

This set-up worked very well. Maximum rapid speed using Mach1 was ~60ipm.

I can't see why it won't have similar performance compared to the gecko for
this size of machine.

The usual disclaimer applies. No relationship with Jeff from Xylotex, other
than a happy customer.

Cheers,


Peter Homann
mailto:Peter.Homann@...
Adacel Technologies Limited,
250 Bay St, BRIGHTON, 3186, AUSTRALIA
http://www.adacel.com <http://www.adacel.com>
Telephone +61 (3) 8530 7777, Facsimile +61 (3) 9596 2960
Mobile 0421-601 665


-----Original Message-----
From: luisguillermo98 [mailto:luisguillermo98@...]
Sent: Thursday, 12 June 2003 11:16 AM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?


Dave,
I am not changing. I have geckos on sherline and I am looking for a
new CNC for my new taig I just got. I am trying to find out if the
xylotex will work as well as the gecko...My volt/current are low I am
wondering if xylotex will give me the same speed and power.


Luis ...

--- In CAD_CAM_EDM_DRO@yahoogroups.com, "turbulatordude"
<davemucha@j...> wrote:
> Hi Luis,
>
> The question I think that I don't have an answer to is why do you
> want to change ?
>
> the motor will get as hot as the power you put thru it. Regardless
> of the driver, if you use 30V and 2 amp, the motor will get exactly
> the same temp.
>
> if you pump more power thru it by increaseing the amps the motor
will
> get hoter.
>
> Also, by reducing your existing set-up to a lower voltage you will
> lose speed, no way around that.
>
> I may have missed if you motor is a 4 wire or 6/8. the 4 is set
and
> does not offer options. if it is a 6 or 8 wire, then you have the
> option of wiring it for a single coil at full amps or series for
half
> amps. the half amps offers a much cooler motor.
>
> either way, a 2 amp rating on a Gecko is low and the Gecko will not
> get hot.
>
> Maybe it would be a good idea to list the nameplate volts and amps,
> wire count and if you are wiring it single coil or series.
>
> What it sounds like is you are trading down for no reason. the 4
> volt motor would be much stronger at 60 volts than 35 volts and a
> series winding will offer a much colder motor.
>
> Dave


Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com

Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
Moderator: pentam@... indigo_red@... [Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner



Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/

Discussion Thread

luisguillermo98 2003-06-08 05:21:36 UTC XYLOTEX VS GECKO DRIVE ?? turbulatordude 2003-06-08 06:34:31 UTC Re: XYLOTEX VS GECKO DRIVE ?? jeffalanp 2003-06-08 10:14:16 UTC Re: XYLOTEX VS GECKO DRIVE ?? Torsten 2003-06-08 11:23:29 UTC Re: XYLOTEX VS GECKO DRIVE ?? turbulatordude 2003-06-08 16:48:21 UTC Re: XYLOTEX VS GECKO DRIVE ?? jeffalanp 2003-06-08 18:06:19 UTC Re: XYLOTEX VS GECKO DRIVE ?? Kim Lux 2003-06-08 18:34:54 UTC Servo motor torque curves and duty cycle info David A. Frantz 2003-06-08 19:17:34 UTC Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info Alan Marconett KM6VV 2003-06-08 19:27:48 UTC Re: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? William Scalione 2003-06-08 19:46:34 UTC Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info Kim Lux 2003-06-09 06:36:51 UTC Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info turbulatordude 2003-06-09 06:57:24 UTC Re: XYLOTEX VS GECKO DRIVE ?? jeffalanp 2003-06-09 11:12:42 UTC Re: XYLOTEX VS GECKO DRIVE ?? luisguillermo98 2003-06-10 17:11:01 UTC Re: XYLOTEX VS GECKO DRIVE ?? Tim Goldstein 2003-06-10 17:35:16 UTC RE: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? jeffalanp 2003-06-10 18:43:47 UTC Re: XYLOTEX VS GECKO DRIVE ?? luisguillermo98 2003-06-10 18:55:21 UTC Re: XYLOTEX VS GECKO DRIVE ?? jeffalanp 2003-06-10 19:41:58 UTC Re: XYLOTEX VS GECKO DRIVE ?? turbulatordude 2003-06-10 20:30:01 UTC Re: XYLOTEX VS GECKO DRIVE ?? why ? William Scalione 2003-06-11 06:23:23 UTC Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info Kim Lux 2003-06-11 06:31:21 UTC Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info Ed Fanta 2003-06-11 06:36:05 UTC Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info Jon Elson 2003-06-11 09:54:47 UTC Re: [CAD_CAM_EDM_DRO] Servo motor torque curves and duty cycle info luisguillermo98 2003-06-11 18:16:09 UTC Re: XYLOTEX VS GECKO DRIVE ?? why ? Peter Homann 2003-06-11 19:04:46 UTC RE: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ? Mark Thomas 2003-06-11 19:06:02 UTC RE: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ? Statman Designs, LLC 2003-06-11 19:59:51 UTC Re: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ? Mark Thomas 2003-06-11 20:20:09 UTC RE: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ? Statman Designs, LLC 2003-06-11 21:04:46 UTC Re: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ? Jon Elson 2003-06-11 21:49:11 UTC Re: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ? Statman Designs, LLC 2003-06-12 04:22:21 UTC Re: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ? luisguillermo98 2003-06-12 19:29:31 UTC Re: XYLOTEX VS GECKO DRIVE ?? why ? Statman Designs, LLC 2003-06-12 22:40:45 UTC Re: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ? Mark Thomas 2003-06-23 15:45:20 UTC RE: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ? Russ Waters 2003-06-25 04:22:04 UTC RE: [CAD_CAM_EDM_DRO] Re: XYLOTEX VS GECKO DRIVE ?? why ?