Re: [CAD_CAM_EDM_DRO] turret tool post for lathe
Posted by
wanliker@a...
on 2003-09-26 08:54:00 UTC
In a message dated 9/26/2003 9:11:09 AM Mountain Daylight Time,
les@... writes:
advantages. If the stepper drove the turret back into the locking position,
wouldn't the holding torque keep it there?
bill
[Non-text portions of this message have been removed]
les@... writes:
> Why use a stepper? The only advantage would be that you could index theI would think that the advantage of programming the tool used, would have
> turret both ways. However you would either need a huge stepper or some form
> of locking mechanism to hold the tool in place while cutting. This adds a
> lot to the cost and complexity.
>
advantages. If the stepper drove the turret back into the locking position,
wouldn't the holding torque keep it there?
bill
[Non-text portions of this message have been removed]
Discussion Thread
digitaldesk2000
2003-09-25 14:45:37 UTC
turret tool post for lathe
Doug Fortune
2003-09-25 21:46:09 UTC
Re: [CAD_CAM_EDM_DRO] turret tool post for lathe
Les Newell
2003-09-26 00:48:14 UTC
Re: [CAD_CAM_EDM_DRO] turret tool post for lathe
wanliker@a...
2003-09-26 07:24:55 UTC
Re: [CAD_CAM_EDM_DRO] turret tool post for lathe
Les Newell
2003-09-26 08:09:57 UTC
Re: [CAD_CAM_EDM_DRO] turret tool post for lathe
wanliker@a...
2003-09-26 08:54:00 UTC
Re: [CAD_CAM_EDM_DRO] turret tool post for lathe
Les Newell
2003-09-26 12:33:22 UTC
Re: [CAD_CAM_EDM_DRO] turret tool post for lathe
Terry Owens
2003-09-26 15:30:32 UTC
Re: [CAD_CAM_EDM_DRO] turret tool post for lathe
Les Newell
2003-09-26 15:39:26 UTC
Re: [CAD_CAM_EDM_DRO] turret tool post for lathe
Alex
2003-09-27 07:23:57 UTC
Re: [CAD_CAM_EDM_DRO] turret tool post for lathe
Les Newell
2003-09-27 10:48:17 UTC
Re: [CAD_CAM_EDM_DRO] turret tool post for lathe
Alex
2003-09-27 20:26:22 UTC
Re: [CAD_CAM_EDM_DRO] turret tool post for lathe
Les Newell
2003-09-27 23:39:41 UTC
Re: [CAD_CAM_EDM_DRO] turret tool post for lathe
doug98105
2003-09-28 09:06:18 UTC
Re: turret tool post for lathe
Les Newell
2003-09-29 01:13:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: turret tool post for lathe
Terry Owens
2003-09-30 08:42:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: turret tool post for lathe
Les Newell
2003-09-30 09:07:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: turret tool post for lathe
Dan Mauch
2003-09-30 10:22:45 UTC
RE: [CAD_CAM_EDM_DRO] Re: turret tool post for lathe
Les Newell
2003-09-30 13:06:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: turret tool post for lathe
Kim Lux
2003-09-30 13:39:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: turret tool post for lathe
Marcus and Eva
2003-09-30 19:23:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: turret tool post for lathe
Terry Owens
2003-10-01 03:26:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: turret tool post for lathe