CAD CAM EDM DRO - Yahoo Group Archive

Re: Hexapod question

Posted by ballendo
on 2003-12-12 06:42:22 UTC
Don,

I was gonna type a long response. Instead, have a look about halfway
down the page at:

http://biotsavart.tripod.com/hexapod.htm

Look at the subheading precision machining, and a bit lower,
Advantages.

Should answer your questions. If not, a search of "Hexapod machining
advantages" turns up lots of hits..

Hope this helps,

Ballendo


--- In CAD_CAM_EDM_DRO@yahoogroups.com, Don Rogers <Don@C...> wrote:
>
> >At first Ballendo I thought the same as you that the extra length
> >beyond the joint would cause a problem but this is not the case.
If
> >those levers as you describe them were shorter the situation would
be
> >exactly the same and if the machine cannot handle a leverage beyond
> >the plane of the pivots then it will not be very good when it comes
> >to milling anything.
>
> OK gang, I have been following this thread for some time now, and I
am still at
> a loss as to what the possible practicable use a Hexapod would be
in a
> machining environment.
>
> I can see that it would give some interesting movements to a table,
but the
> simple lever
> arm lengths involved would, it seems to me, eliminate this design
as a
> practical tool for
> machining metals. Am I missing something here? Or am I narrowing
my view
> to much?
>
> Don

Discussion Thread

Simon M. Arthur 2003-12-09 06:56:50 UTC Hexapod question Jon Elson 2003-12-09 09:40:28 UTC Re: [CAD_CAM_EDM_DRO] Hexapod question Graham Stabler 2003-12-09 11:37:45 UTC Re: Hexapod question Graham Stabler 2003-12-09 11:45:25 UTC Re: Hexapod question Kevin Martin 2003-12-09 13:23:54 UTC RE: [CAD_CAM_EDM_DRO] Hexapod question Simon M. Arthur 2003-12-09 21:55:33 UTC Re: Hexapod question Simon M. Arthur 2003-12-09 21:55:34 UTC Re: Hexapod question Graham Stabler 2003-12-10 05:07:25 UTC Re: Hexapod question Ray Henry 2003-12-10 05:43:54 UTC Re: Hexapod question Asim Khan 2003-12-10 06:32:58 UTC EMC related Question G54 G55,... and use of 5241, 5242, 5243 variables [asimtec] Tim 2003-12-10 08:38:43 UTC Re: Hexapod question Madhu Annapragada 2003-12-10 09:13:24 UTC RE: [CAD_CAM_EDM_DRO] Re: Hexapod question Mariss Freimanis 2003-12-10 10:03:33 UTC Re: Hexapod question Carl Mikkelsen 2003-12-10 10:38:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Hexapod question Jon Elson 2003-12-10 10:59:20 UTC Re: [CAD_CAM_EDM_DRO] Re: Hexapod question Chuck Knight 2003-12-10 11:00:07 UTC Re: [CAD_CAM_EDM_DRO] Hexapod question Jon Elson 2003-12-10 11:03:17 UTC Re: [CAD_CAM_EDM_DRO] Re: Hexapod question Chuck Knight 2003-12-10 11:47:04 UTC Re: [CAD_CAM_EDM_DRO] Re: Hexapod question Carl Mikkelsen 2003-12-10 13:10:45 UTC Re: [CAD_CAM_EDM_DRO] Hexapod question industrialhobbies 2003-12-10 14:08:30 UTC Re: Hexapod question Jon Elson 2003-12-10 14:59:06 UTC Re: [CAD_CAM_EDM_DRO] EMC related Question G54 G55,... and use of 5241, 5242, 5243 variables [asimtec] Graham Stabler 2003-12-10 15:31:11 UTC Re: Hexapod question Simon M. Arthur 2003-12-10 15:34:45 UTC Re: Hexapod question Paul 2003-12-10 16:42:46 UTC Re: [CAD_CAM_EDM_DRO] Re: Hexapod question Richard L. Wurdack 2003-12-10 17:27:51 UTC Re: [CAD_CAM_EDM_DRO] Re: Hexapod question Harvey White 2003-12-10 18:45:58 UTC Re: [cad-cam] [CAD_CAM_EDM_DRO] Re: Hexapod question Simon M. Arthur 2003-12-10 19:07:39 UTC Re: [CAD_CAM_EDM_DRO] Re: Hexapod question Ray Henry 2003-12-10 22:43:36 UTC Re: Re: Hexapod question Jon Elson 2003-12-11 03:55:25 UTC Re: [CAD_CAM_EDM_DRO] Re: Hexapod question Ray Henry 2003-12-11 06:52:18 UTC Re: Re: Re: Hexapod question alex 2003-12-11 07:32:39 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Re: Hexapod question ballendo 2003-12-11 11:48:35 UTC Re: Hexapod question Jon Elson 2003-12-11 14:43:33 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Re: Hexapod question Kevin Martin 2003-12-11 16:18:35 UTC RE: [CAD_CAM_EDM_DRO] Re: Hexapod question afaIII 2003-12-11 18:12:22 UTC Re: Hexapod question (joints) alex 2003-12-11 18:37:32 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Re: Hexapod question Graham Stabler 2003-12-11 19:11:43 UTC Re: Hexapod question Raymond Heckert 2003-12-11 20:46:06 UTC Re: [CAD_CAM_EDM_DRO] Re: Hexapod question industrialhobbies 2003-12-11 21:09:05 UTC Re: Hexapod question (joints) Don Rogers 2003-12-11 23:11:54 UTC Re: Hexapod question Graham Stabler 2003-12-12 02:29:01 UTC Re: Hexapod question Indy123456 2003-12-12 05:18:32 UTC Re: Hexapod question ballendo 2003-12-12 06:41:38 UTC Re: Hexapod question ballendo 2003-12-12 06:42:22 UTC Re: Hexapod question ballendo 2003-12-12 06:42:31 UTC Re: Hexapod question ballendo 2003-12-12 06:42:55 UTC Re: Hexapod question ballendo 2003-12-12 06:42:56 UTC Re: Hexapod question afaIII 2003-12-12 07:31:08 UTC Re: Hexapod question Raymond Heckert 2003-12-12 18:07:07 UTC Re: [CAD_CAM_EDM_DRO] Re: Hexapod question Ray Henry 2003-12-13 06:56:21 UTC Re: Re: Hexapod question cadcracker@l... 2003-12-13 12:49:33 UTC Re: [CAD_CAM_EDM_DRO] Re: Hexapod question Dave Dillabough 2003-12-15 13:24:20 UTC Re: [CAD_CAM_EDM_DRO] Re: Hexapod question doug98105 2003-12-15 16:23:07 UTC Re: Hexapod question