CAD CAM EDM DRO - Yahoo Group Archive

RE: jerry's power supply .pdf

Posted by keith
on 2004-03-04 07:29:46 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, JanRwl@A... wrote:
> In a message dated 3/3/2004 10:16:10 AM Central Standard Time,
> jasonkth@w... writes:
> jerry's power supply .pdf
> Where? AOL search can NOT find this!
>
>
> [Non-text portions of this message have been removed]

the file "jerry's power supply .pdf" is located on this groups files
section under circuits\power supplies. i figured out that i just
need to insulate the center tap wire on the secondary and the same
for the second half winding (red wire) on the primary, as i'm setting
it up on 110. if anyone has used this power supply, and added other
features,(soft start/snubber/shunt) i would like to hear about it. i
finished wiring the basic schematic today, but haven't powered it up
yet cuz i don't want to leave the capacitor charged up while i work
with it, and i'm not sure how to discharge it properly. i'm wishin i
had paid more attention in electronics class in school!! i also have
to wire up a test cable to run r990h.exe to test the drive (and my
setup!). the pile of components on the table is slowly coming
together. :)

Discussion Thread

Jon Elson 2000-11-16 15:05:39 UTC Re: [CAD_CAM_EDM_DRO] (unknown) Carey L. Culpepper 2000-12-14 07:21:55 UTC Re: [CAD_CAM_EDM_DRO] (unknown) Jon Elson 2000-12-19 13:19:13 UTC Re: [CAD_CAM_EDM_DRO] (unknown) wanliker@a... 2001-01-11 16:08:28 UTC Re: [CAD_CAM_EDM_DRO] (unknown) Smoke 2001-11-24 09:45:06 UTC Re: [CAD_CAM_EDM_DRO] (unknown) catboat15@a... 2002-02-17 20:29:08 UTC Re: [CAD_CAM_EDM_DRO] (unknown) Jon Elson 2002-02-17 22:30:18 UTC Re: [CAD_CAM_EDM_DRO] (unknown) Jon Elson 2002-02-17 22:40:42 UTC Re: [CAD_CAM_EDM_DRO] (unknown) catboat15@a... 2002-02-18 07:43:28 UTC Re: [CAD_CAM_EDM_DRO] (unknown) Dan Mauch 2002-06-26 10:01:26 UTC RE: [CAD_CAM_EDM_DRO] (unknown) luisguillermo98 2002-06-26 12:21:39 UTC Re: (unknown) bilg63475 2002-06-26 13:56:55 UTC Re: (unknown) luisguillermo98 2002-06-26 15:31:59 UTC Re: (unknown) Shelbyville Design & Signworks 2002-07-11 14:31:41 UTC Re: [CAD_CAM_EDM_DRO] (unknown) Doug Harrison 2002-07-11 15:47:15 UTC Re: [CAD_CAM_EDM_DRO] (unknown) Jon Elson 2002-10-08 11:08:19 UTC Re: [CAD_CAM_EDM_DRO] (unknown) Art 2002-11-03 16:14:49 UTC Re: [CAD_CAM_EDM_DRO] (unknown) Jon Elson 2002-12-10 22:53:08 UTC Re: [CAD_CAM_EDM_DRO] (unknown) Raymond Heckert 2002-12-11 15:42:04 UTC Re: [CAD_CAM_EDM_DRO] (unknown) Robert Campbell 2003-05-28 07:29:36 UTC Re: [CAD_CAM_EDM_DRO] (unknown) R Petersen 2003-05-28 20:34:07 UTC Re: [CAD_CAM_EDM_DRO] (unknown)CNC rebuild help Brian 2003-08-16 05:44:55 UTC Re: [CAD_CAM_EDM_DRO] (unknown) Jon Elson 2003-10-21 10:35:06 UTC Re: [CAD_CAM_EDM_DRO] (unknown) JanRwl@A... 2004-03-03 12:35:40 UTC Re: [CAD_CAM_EDM_DRO] (unknown) Monte 2004-03-04 06:35:28 UTC Re: (unknown) keith 2004-03-04 07:29:46 UTC RE: jerry's power supply .pdf