Re: [CAD_CAM_EDM_DRO] (unknown)
Posted by
Jon Elson
on 2002-10-08 11:08:19 UTC
builder4wd wrote:
the Sherline like they were toothpicks! peak torque of 29 in-lb =
464 in-Oz! This would be fine on a full-size Bridgeport machine!
You can drive a Sherline with much smaller motors. At 4.6 Lbs,
these motors at least won't break the table in half. But, you will
have to set the current limit WELL below the max to avoid wrecking
your machine.
Jon
> Hi, I own a sherline lathe, and I'm planning on getting a SherlineYou've got to be kidding! This motor could snap the leadscrews on
> mill and converting it to CNC. I've been lurking here awhile, and
> looking at webpages, but I'm still not very clear about this stuff.
>
> Anyways...
> Would the API MBT-N232 motor work well for my application?:
> http://www.apicontrols.com/newapi/products/turbo_mbt23.html
>
> It has 9.8 lb-in of stall torque and I think it is size #23.
>
> Would this be good with the gecko G320 drive?
the Sherline like they were toothpicks! peak torque of 29 in-lb =
464 in-Oz! This would be fine on a full-size Bridgeport machine!
You can drive a Sherline with much smaller motors. At 4.6 Lbs,
these motors at least won't break the table in half. But, you will
have to set the current limit WELL below the max to avoid wrecking
your machine.
Jon
Discussion Thread
Jon Elson
2000-11-16 15:05:39 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Carey L. Culpepper
2000-12-14 07:21:55 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Jon Elson
2000-12-19 13:19:13 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
wanliker@a...
2001-01-11 16:08:28 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Smoke
2001-11-24 09:45:06 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
catboat15@a...
2002-02-17 20:29:08 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Jon Elson
2002-02-17 22:30:18 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Jon Elson
2002-02-17 22:40:42 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
catboat15@a...
2002-02-18 07:43:28 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Dan Mauch
2002-06-26 10:01:26 UTC
RE: [CAD_CAM_EDM_DRO] (unknown)
luisguillermo98
2002-06-26 12:21:39 UTC
Re: (unknown)
bilg63475
2002-06-26 13:56:55 UTC
Re: (unknown)
luisguillermo98
2002-06-26 15:31:59 UTC
Re: (unknown)
Shelbyville Design & Signworks
2002-07-11 14:31:41 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Doug Harrison
2002-07-11 15:47:15 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Jon Elson
2002-10-08 11:08:19 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Art
2002-11-03 16:14:49 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Jon Elson
2002-12-10 22:53:08 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Raymond Heckert
2002-12-11 15:42:04 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Robert Campbell
2003-05-28 07:29:36 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
R Petersen
2003-05-28 20:34:07 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)CNC rebuild help
Brian
2003-08-16 05:44:55 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Jon Elson
2003-10-21 10:35:06 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
JanRwl@A...
2004-03-03 12:35:40 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Monte
2004-03-04 06:35:28 UTC
Re: (unknown)
keith
2004-03-04 07:29:46 UTC
RE: jerry's power supply .pdf