Re: [CAD_CAM_EDM_DRO] (unknown)
Posted by
wanliker@a...
on 2001-01-11 16:08:28 UTC
In a message dated 1/11/01 3:42:11 PM Mountain Standard Time,
smcleod007@... writes:
<< I was curious if anyone here at 'egroups', has any experience
with "Motion Direct Inc.", or any opinons of their
software. >>
There encoders look a lot like the ones I used at work, but they drove
potentiometers, I am not sure how theirs are configured. But they could
easily be made at home and drive an encoder. And used with the doubling
system that was discussed earlier on the list, I would think they would have
very good resolution.
bill
smcleod007@... writes:
<< I was curious if anyone here at 'egroups', has any experience
with "Motion Direct Inc.", or any opinons of their
software. >>
There encoders look a lot like the ones I used at work, but they drove
potentiometers, I am not sure how theirs are configured. But they could
easily be made at home and drive an encoder. And used with the doubling
system that was discussed earlier on the list, I would think they would have
very good resolution.
bill
Discussion Thread
Jon Elson
2000-11-16 15:05:39 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Carey L. Culpepper
2000-12-14 07:21:55 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Jon Elson
2000-12-19 13:19:13 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
wanliker@a...
2001-01-11 16:08:28 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Smoke
2001-11-24 09:45:06 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
catboat15@a...
2002-02-17 20:29:08 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Jon Elson
2002-02-17 22:30:18 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Jon Elson
2002-02-17 22:40:42 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
catboat15@a...
2002-02-18 07:43:28 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Dan Mauch
2002-06-26 10:01:26 UTC
RE: [CAD_CAM_EDM_DRO] (unknown)
luisguillermo98
2002-06-26 12:21:39 UTC
Re: (unknown)
bilg63475
2002-06-26 13:56:55 UTC
Re: (unknown)
luisguillermo98
2002-06-26 15:31:59 UTC
Re: (unknown)
Shelbyville Design & Signworks
2002-07-11 14:31:41 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Doug Harrison
2002-07-11 15:47:15 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Jon Elson
2002-10-08 11:08:19 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Art
2002-11-03 16:14:49 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Jon Elson
2002-12-10 22:53:08 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Raymond Heckert
2002-12-11 15:42:04 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Robert Campbell
2003-05-28 07:29:36 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
R Petersen
2003-05-28 20:34:07 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)CNC rebuild help
Brian
2003-08-16 05:44:55 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Jon Elson
2003-10-21 10:35:06 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
JanRwl@A...
2004-03-03 12:35:40 UTC
Re: [CAD_CAM_EDM_DRO] (unknown)
Monte
2004-03-04 06:35:28 UTC
Re: (unknown)
keith
2004-03-04 07:29:46 UTC
RE: jerry's power supply .pdf