Re: Gecko 210s l- limited rapids
Posted by
Keith Clark
on 2004-08-20 19:41:30 UTC
Steven,
I thought they were Nema 34 but the spec I just reviewed says they
are 4.2 inch diameter. Does that make them Nema 42? I do not find
any information about such a jumper.
It looks like there is a #10 terminal that is supposed to be
connected to the common 5vdc power supply but it is not connected.
I wonder if that could be part of the problem?
Keith
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Steven Ciciora"
<sciciora@A...> wrote:
I thought they were Nema 34 but the spec I just reviewed says they
are 4.2 inch diameter. Does that make them Nema 42? I do not find
any information about such a jumper.
It looks like there is a #10 terminal that is supposed to be
connected to the common 5vdc power supply but it is not connected.
I wonder if that could be part of the problem?
Keith
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Steven Ciciora"
<sciciora@A...> wrote:
> Doesn't the Gecko Drive have a jumper for Nema 42 motors? Is itset correctly?
>with 7
>
> - Steven Ciciora
>
> >Sigma motor, 9 amp, Gecko 210 set at 200 steps per revolution
> >amp max power. Motors wired in half winding mode. There is noreduction
> >excess mechanical load. Power supply 75 volt 16 amp. 2:1
> >with 5 pitch lead screw. Using Galil motion control board.Still
> >only about 30 ipm maximum before stalling.from
> >
> >Everything seems to be working fine at lower speeds. How can I
> >pursue the possibility of getting some better axis motor speeds
> >these drives?before
> >
> >I expected even greater rapids than the 100ipm the Boss 6 had
> >the retrofit, according the sales pitch I was given...wanliker@a..., timg@k...
> >
> >Thought I'd ask one more time.
> >
> >Keith Clark
> >
> >
> >
> >Addresses:
> >FAQ: http://www.ktmarketing.com/faq.html
> >FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> >Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> >
> >Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> >Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> >List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
>[Moderators]
> >Moderator: pentam@c... indigo_red@q... davemucha@j...
>aol://5863:126/rec.crafts.metalworking
> >URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> >
> >OFF Topic POSTS: General Machining
> >If you wish to post on unlimited OT subjects goto:
> or go thru Google.com to reach it if you have trouble.to be a sister
> >http://www.metalworking.com/news_servers.html
> >
> >http://groups.yahoo.com/group/jobshophomeshop I consider this
> site to the CCED group, as many of the same members are there, forOT subjects,
> that are not allowed on the CCED list.POSTING THEM. DON'T
> >
> >NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
> POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> >bill
> >List Mom
> >List Owner
> >
> >
> >Yahoo! Groups Links
> >
> >
> >
> >
> >
> >
Discussion Thread
theokspindoctor
2004-08-20 18:41:13 UTC
Gecko 210s l- limited rapids
Steven Ciciora
2004-08-20 18:53:41 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 210s l- limited rapids
Torsten
2004-08-20 19:09:34 UTC
Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-20 19:29:30 UTC
Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-20 19:41:30 UTC
Re: Gecko 210s l- limited rapids
skykotech
2004-08-20 20:02:26 UTC
Re: Gecko 210s l- limited rapids
Ron K
2004-08-20 20:14:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids
Jon Elson
2004-08-20 21:33:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-20 22:29:53 UTC
Re: Gecko 210s l- limited rapids
Jon Elson
2004-08-21 12:05:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-21 12:36:19 UTC
Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-21 13:15:17 UTC
Re: Gecko 210s l- limited rapids
Jon Elson
2004-08-21 21:42:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids
Jon Elson
2004-08-21 21:50:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-22 15:12:24 UTC
Re: Gecko 210s l- limited rapids
Jon Elson
2004-08-22 22:48:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids