Re: Gecko 210s l- limited rapids
Posted by
Keith Clark
on 2004-08-21 12:36:19 UTC
Jon, Thanks so much, the documentation that came with my Geckos was
the last year version and it did not document the nema 42 switch but
the new revision on the website did! Hope that fixes me up.
Do you have any insight into where to find the selonoids that
control the air brake and spindle speed. The switches are still
wired but I have lost power to them. There is not enough info in the
schematic to tell which wires.
thanks
Keith Clark
the last year version and it did not document the nema 42 switch but
the new revision on the website did! Hope that fixes me up.
Do you have any insight into where to find the selonoids that
control the air brake and spindle speed. The switches are still
wired but I have lost power to them. There is not enough info in the
schematic to tell which wires.
thanks
Keith Clark
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Jon Elson <elson@p...> wrote:
> Keith Clark wrote:
>
> >I took apart the drives and found that term 10 was actually
> >connected to the 5vdc as it should be. The multiplex board
jumper
> >is set to common +5vdc. Is that correct?
> >
> >Is there a jumper for Nema 42 motors, I could not find it.
> >
> >
> If you don't have the "G201 Rev 5 Installation Notes" from Gecko,
> download it from their G201 web page. (There's a dead link to a
> "coming soon" pdf file, but one of the links gets you a 3 page
document
> with all the info on jumpers, etc.)
>
> From that document, there is an 8-pin jumper block on the main
board
> (this would be the lower board on a G210).
>
> Bad ascii art follows :
>
> Big 1 2 3 4 corner
> CAP 5 6 7 8 of board
>
> There is probably a jumper on 2 to 6, which is enabling the
> standby current reduction. Normal mid-band damping has a
> jumper from 7 to 8. For a size 42 motor, you should move jumper
> from 3 to 7. You still want to adjust the damping pot for minimum
> vibration when running the motor at a speed of about 15 RPM.
>
> Jon
Discussion Thread
theokspindoctor
2004-08-20 18:41:13 UTC
Gecko 210s l- limited rapids
Steven Ciciora
2004-08-20 18:53:41 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 210s l- limited rapids
Torsten
2004-08-20 19:09:34 UTC
Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-20 19:29:30 UTC
Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-20 19:41:30 UTC
Re: Gecko 210s l- limited rapids
skykotech
2004-08-20 20:02:26 UTC
Re: Gecko 210s l- limited rapids
Ron K
2004-08-20 20:14:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids
Jon Elson
2004-08-20 21:33:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-20 22:29:53 UTC
Re: Gecko 210s l- limited rapids
Jon Elson
2004-08-21 12:05:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-21 12:36:19 UTC
Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-21 13:15:17 UTC
Re: Gecko 210s l- limited rapids
Jon Elson
2004-08-21 21:42:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids
Jon Elson
2004-08-21 21:50:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-22 15:12:24 UTC
Re: Gecko 210s l- limited rapids
Jon Elson
2004-08-22 22:48:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids