Re: [CAD_CAM_EDM_DRO] Gecko 210s l- limited rapids
Posted by
Steven Ciciora
on 2004-08-20 18:53:41 UTC
Doesn't the Gecko Drive have a jumper for Nema 42 motors? Is it set correctly?
- Steven Ciciora
that are not allowed on the CCED list.
- Steven Ciciora
>Sigma motor, 9 amp, Gecko 210 set at 200 steps per revolution with 7or go thru Google.com to reach it if you have trouble.
>amp max power. Motors wired in half winding mode. There is no
>excess mechanical load. Power supply 75 volt 16 amp. 2:1 reduction
>with 5 pitch lead screw. Using Galil motion control board. Still
>only about 30 ipm maximum before stalling.
>
>Everything seems to be working fine at lower speeds. How can I
>pursue the possibility of getting some better axis motor speeds from
>these drives?
>
>I expected even greater rapids than the 100ipm the Boss 6 had before
>the retrofit, according the sales pitch I was given...
>
>Thought I'd ask one more time.
>
>Keith Clark
>
>
>
>Addresses:
>FAQ: http://www.ktmarketing.com/faq.html
>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
>Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
>URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
>OFF Topic POSTS: General Machining
>If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking
>http://www.metalworking.com/news_servers.htmlsite to the CCED group, as many of the same members are there, for OT subjects,
>
>http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister
that are not allowed on the CCED list.
>POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
>NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T
>bill
>List Mom
>List Owner
>
>
>Yahoo! Groups Links
>
>
>
>
>
>
Discussion Thread
theokspindoctor
2004-08-20 18:41:13 UTC
Gecko 210s l- limited rapids
Steven Ciciora
2004-08-20 18:53:41 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 210s l- limited rapids
Torsten
2004-08-20 19:09:34 UTC
Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-20 19:29:30 UTC
Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-20 19:41:30 UTC
Re: Gecko 210s l- limited rapids
skykotech
2004-08-20 20:02:26 UTC
Re: Gecko 210s l- limited rapids
Ron K
2004-08-20 20:14:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids
Jon Elson
2004-08-20 21:33:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-20 22:29:53 UTC
Re: Gecko 210s l- limited rapids
Jon Elson
2004-08-21 12:05:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-21 12:36:19 UTC
Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-21 13:15:17 UTC
Re: Gecko 210s l- limited rapids
Jon Elson
2004-08-21 21:42:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids
Jon Elson
2004-08-21 21:50:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-22 15:12:24 UTC
Re: Gecko 210s l- limited rapids
Jon Elson
2004-08-22 22:48:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids