Re: Gecko 210s l- limited rapids
Posted by
Torsten
on 2004-08-20 19:09:34 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "theokspindoctor" <mail@t...>
wrote:
300 rpm x 200 steps per rev.= 60 000 steps per minute / 60 seconds
= 1000 steps per sec or 1k steps.
this is far less then the gecko's are capable of.
what is the rated rpm of these motors?
wrote:
> Sigma motor, 9 amp, Gecko 210 set at 200 steps per revolution with7
> amp max power. Motors wired in half winding mode. There is nofrom
> excess mechanical load. Power supply 75 volt 16 amp. 2:1 reduction
> with 5 pitch lead screw. Using Galil motion control board. Still
> only about 30 ipm maximum before stalling.
>
> Everything seems to be working fine at lower speeds. How can I
> pursue the possibility of getting some better axis motor speeds
> these drives?before
>
> I expected even greater rapids than the 100ipm the Boss 6 had
> the retrofit, according the sales pitch I was given...30ipm x 5 pitch leadscrew = 150 x 2/1 ratio = 300 rpm on the motor
>
300 rpm x 200 steps per rev.= 60 000 steps per minute / 60 seconds
= 1000 steps per sec or 1k steps.
this is far less then the gecko's are capable of.
what is the rated rpm of these motors?
Discussion Thread
theokspindoctor
2004-08-20 18:41:13 UTC
Gecko 210s l- limited rapids
Steven Ciciora
2004-08-20 18:53:41 UTC
Re: [CAD_CAM_EDM_DRO] Gecko 210s l- limited rapids
Torsten
2004-08-20 19:09:34 UTC
Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-20 19:29:30 UTC
Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-20 19:41:30 UTC
Re: Gecko 210s l- limited rapids
skykotech
2004-08-20 20:02:26 UTC
Re: Gecko 210s l- limited rapids
Ron K
2004-08-20 20:14:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids
Jon Elson
2004-08-20 21:33:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-20 22:29:53 UTC
Re: Gecko 210s l- limited rapids
Jon Elson
2004-08-21 12:05:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-21 12:36:19 UTC
Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-21 13:15:17 UTC
Re: Gecko 210s l- limited rapids
Jon Elson
2004-08-21 21:42:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids
Jon Elson
2004-08-21 21:50:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids
Keith Clark
2004-08-22 15:12:24 UTC
Re: Gecko 210s l- limited rapids
Jon Elson
2004-08-22 22:48:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko 210s l- limited rapids