Re: Servomotors & Minimill - do these need speed reduction or not?
Posted by
turbulatordude
on 2004-09-15 07:33:17 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, R Rogers <rogersmach@y...>
wrote:
use them. The drives are much more expensive, alot more difficult to
configure. Heating problems compared to servos etc. I've just noticed
alot of posts with questions regarding steppers and I'm just confused
why anyone would use them. There seems to be an abundance of used
servos around. One person one here mentioned that "the steppers on
his small mini-lathe produced enough heat to fry eggs"
Also, because most people do not know where the 'abundance or
servo's' are and/or don't want to get involved with encoders as there
are not a lot of cheap encoders around.
Steppers offer the power at cutting speeds so in that way, are ideal
for home-brew.
Stepper drivers are easy to make, find or buy.
There are a few complete stepper packages for small machines that
sell for under $200.00
I don't know of any servo packages that are that low cost.
Dave
wrote:
> The low rapid rate and general lack of torque at high speed seemsto be the case with steppers. I'm wondering why anyone would opt to
use them. The drives are much more expensive, alot more difficult to
configure. Heating problems compared to servos etc. I've just noticed
alot of posts with questions regarding steppers and I'm just confused
why anyone would use them. There seems to be an abundance of used
servos around. One person one here mentioned that "the steppers on
his small mini-lathe produced enough heat to fry eggs"
>Becasue steppers are so dang easy to use.
> Ron
Also, because most people do not know where the 'abundance or
servo's' are and/or don't want to get involved with encoders as there
are not a lot of cheap encoders around.
Steppers offer the power at cutting speeds so in that way, are ideal
for home-brew.
Stepper drivers are easy to make, find or buy.
There are a few complete stepper packages for small machines that
sell for under $200.00
I don't know of any servo packages that are that low cost.
Dave
Discussion Thread
grantfair2001
2004-09-14 00:56:27 UTC
Servomotors & Minimill - do these need speed reduction or not?
knives01us
2004-09-14 03:03:48 UTC
Re: Servomotors & Minimill - do these need speed reduction or not?
Jon Elson
2004-09-14 10:20:38 UTC
Re: [CAD_CAM_EDM_DRO] Servomotors & Minimill - do these need speed reduction or not?
Jon Elson
2004-09-14 10:22:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servomotors & Minimill - do these need speed reduction or not?
R Rogers
2004-09-14 11:09:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servomotors & Minimill - do these need speed reduction or not?
Jon Elson
2004-09-14 18:48:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servomotors & Minimill - do these need speed reduction or not?
turbulatordude
2004-09-15 07:33:17 UTC
Re: Servomotors & Minimill - do these need speed reduction or not?
R Rogers
2004-09-15 08:36:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servomotors & Minimill - do these need speed reduction or not?
turbulatordude
2004-09-15 09:57:38 UTC
Re: Servomotors & Minimill - do these need speed reduction or not?
Fred Smith
2004-09-15 13:09:23 UTC
Re: Servomotors & Minimill - do these need speed reduction or not?
Larry Wright
2004-09-15 13:17:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servomotors & Minimill - do these need speed reduction or not?
erie
2004-09-15 14:14:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servomotors & Minimill - do these need speed reduction or not?
AbbyKatt
2004-09-15 14:31:50 UTC
Piggy-Backing Gecko 320's Error channels -> E-stop
R Rogers
2004-09-15 15:11:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servomotors & Minimill - do these need speed reduction or not?
R Rogers
2004-09-15 15:19:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servomotors & Minimill - do these need speed reduction or not?
erie
2004-09-15 15:27:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servomotors & Minimill - do these need speed reduction or not?
Simon Arthur
2004-09-15 16:22:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servomotors & Minimill - do these need speed reduction or not?
Fred Smith
2004-09-15 16:53:35 UTC
Re: Servomotors & Minimill - do these need speed reduction or not?