Re: Knee for z-axis control?
Posted by
Fred Smith
on 2004-09-17 12:43:35 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, R Rogers <rogersmach@y...>
wrote:
fact it is actually balanced atop the lead screw and stantion.
Move the table all the way forward, and then all the way to the right
or left, with a couple hundred pound load at the end, and see if the
table lock makes a difference.
Fred Smith - IMService
THE source for low cost Cad-Cam
Group discounts and specials are at:
http://www.cadcamcadcam.com/hobby
wrote:
>Some apparently have the misconception that the knee "hangs" off ofthe Bridgeport and is imposing a large side load on the ways, when in
fact it is actually balanced atop the lead screw and stantion.
Move the table all the way forward, and then all the way to the right
or left, with a couple hundred pound load at the end, and see if the
table lock makes a difference.
Fred Smith - IMService
THE source for low cost Cad-Cam
Group discounts and specials are at:
http://www.cadcamcadcam.com/hobby
Discussion Thread
pondindustrial
2004-09-15 13:23:00 UTC
Knee for z-axis control?
Stephen Wille Padnos
2004-09-15 14:30:51 UTC
Re: [CAD_CAM_EDM_DRO] Knee for z-axis control?
R Rogers
2004-09-15 16:12:20 UTC
Re: [CAD_CAM_EDM_DRO] Knee for z-axis control?
Fred Smith
2004-09-15 17:04:51 UTC
Re: Knee for z-axis control?
pondindustrial
2004-09-15 17:39:16 UTC
Re: Knee for z-axis control?
R Rogers
2004-09-15 18:26:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Knee for z-axis control?
R Rogers
2004-09-15 18:42:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: Knee for z-axis control?
Jon Elson
2004-09-15 19:30:43 UTC
Re: [CAD_CAM_EDM_DRO] Knee for z-axis control?
Jon Elson
2004-09-15 19:36:59 UTC
Re: [CAD_CAM_EDM_DRO] Knee for z-axis control?
Stephen Wille Padnos
2004-09-15 19:58:29 UTC
Re: [CAD_CAM_EDM_DRO] Knee for z-axis control?
Peter Renolds
2004-09-15 20:15:24 UTC
Re: [CAD_CAM_EDM_DRO] Knee for z-axis control?
Peter Renolds
2004-09-15 20:47:19 UTC
Re: [CAD_CAM_EDM_DRO] Knee for z-axis control?
Jon Elson
2004-09-15 22:13:50 UTC
Re: [CAD_CAM_EDM_DRO] Knee for z-axis control?
R Rogers
2004-09-16 07:48:14 UTC
Re: [CAD_CAM_EDM_DRO] Knee for z-axis control?
doug98105
2004-09-16 13:28:03 UTC
Re: Knee for z-axis control?
jlsmith269
2004-09-16 14:28:38 UTC
Re: Knee for z-axis control?
Bob Muse
2004-09-16 14:29:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Knee for z-axis control?
R Rogers
2004-09-16 15:00:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Knee for z-axis control?
doug98105
2004-09-16 16:12:39 UTC
Re: Knee for z-axis control?
metlmunchr
2004-09-16 16:33:14 UTC
Re: Knee for z-axis control?
Peter Renolds
2004-09-16 16:35:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: Knee for z-axis control?
Larry Wright
2004-09-16 16:59:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: Knee for z-axis control?
Sven-Åke Larsson
2004-09-17 00:38:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: Knee for z-axis control?
pondindustrial
2004-09-17 09:29:02 UTC
Re: Knee for z-axis control?
Fred Smith
2004-09-17 09:44:33 UTC
Re: Knee for z-axis control?
R Rogers
2004-09-17 11:42:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Knee for z-axis control?
Fred Smith
2004-09-17 12:43:35 UTC
Re: Knee for z-axis control?
R Rogers
2004-09-17 13:11:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: Knee for z-axis control?
Fred Smith
2004-09-17 14:24:48 UTC
Re: Knee for z-axis control?
R Rogers
2004-09-17 15:03:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Knee for z-axis control?
Paul
2004-09-17 16:45:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Knee for z-axis control?
pondindustrial
2004-09-17 17:19:03 UTC
Re: Knee for z-axis control?
Brian
2004-09-17 18:04:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Knee for z-axis control?
R Rogers
2004-09-17 19:43:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Knee for z-axis control?
wanliker@a...
2004-09-17 23:29:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Knee for z-axis control?
pondindustrial
2004-09-17 23:49:49 UTC
Re: Knee for z-axis control?
alenou arakar
2004-09-18 06:43:29 UTC
Re: Re: Knee for z-axis control? 4 holes ? and EDM
jlsmith269
2004-09-19 09:43:39 UTC
Re: Knee for z-axis control?
Fred Smith
2004-09-19 10:36:31 UTC
Re: Knee for z-axis control?
Jon Elson
2004-09-19 13:00:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Knee for z-axis control?
industrialhobbies
2004-09-21 00:48:03 UTC
Re: Knee for z-axis control?
volitan712003
2004-09-22 17:29:18 UTC
Re: Knee for z-axis control?
turbulatordude
2004-09-22 18:26:12 UTC
Re: Knee for z-axis control? pnuematic actuator
Stephen Wille Padnos
2004-09-22 18:38:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Knee for z-axis control? pnuematic actuator
Jon Elson
2004-09-22 21:34:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Knee for z-axis control? pnuematic actuator
R Rogers
2004-09-23 09:25:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Knee for z-axis control?
Peter Renolds
2004-09-23 17:43:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Knee for z-axis control?
R Rogers
2004-09-23 19:25:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Knee for z-axis control?
volitan712003
2004-09-23 19:27:38 UTC
Re: Knee for z-axis control?
Peter Renolds
2004-09-24 05:24:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Knee for z-axis control?