Re: Rolled vs. Ground ballscrews or other screws!
Posted by
Lance Hopper
on 2005-09-19 19:49:40 UTC
I've run a Bridgeport with ballscrews for a couple years. It was a
beautiful experience in all situations. Climb milling is possible
with smaller cutters and lighter cuts, but any backlash or slop will
be violently taken up if the cutter digs in. Save climb milling with
2" face mills and heavier cuts for the machining centers. I don't
doubt that anything is impossible, but to throw the table off of the
machine means that the operator is a dumba** and has no sense
or 'feel' for how to machine.
I picked up a set of Rockford ballscrews from Ebay a while back for
my personal Bridgeport. Unfortunately, I've yet to have the downtime
to install them.
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "turbulatordude"
<dave_mucha@y...> wrote:
beautiful experience in all situations. Climb milling is possible
with smaller cutters and lighter cuts, but any backlash or slop will
be violently taken up if the cutter digs in. Save climb milling with
2" face mills and heavier cuts for the machining centers. I don't
doubt that anything is impossible, but to throw the table off of the
machine means that the operator is a dumba** and has no sense
or 'feel' for how to machine.
I picked up a set of Rockford ballscrews from Ebay a while back for
my personal Bridgeport. Unfortunately, I've yet to have the downtime
to install them.
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "turbulatordude"
<dave_mucha@y...> wrote:
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "Polaraligned"into
> <polaraligned@o...> wrote:
> > George,
> >
> > If you convert to ballscrews to be used manually in
> > preperation for CNC conversion, you may want to be
> > careful when climb milling. I think it can be a bit
> > dangerous with ballscrews because of their very low friction.
> >
> >
> > Scott
>
> The bridgeprot repairman said to NEVER EVER run a ball-screw machine
> by hand.
>
> the only times he had ever seen the table shoot off the rails and
> a wall were on two seperate ballscrew machines that were being runbut
> manually.
>
> I know of no other person that claims to have seen such a problem,
> ball screws do not have the resistance or self stopping conditionsof
> ACME screws.
>
>
> Dave
Discussion Thread
Jim Colley
2005-09-18 15:25:20 UTC
Rolled vs. Ground ballscrews
turbulatordude
2005-09-18 15:31:38 UTC
Re: Rolled vs. Ground ballscrews
Les Newell
2005-09-18 15:43:27 UTC
Re: [CAD_CAM_EDM_DRO] Rolled vs. Ground ballscrews
Dan Mauch
2005-09-18 16:29:51 UTC
Re: [CAD_CAM_EDM_DRO] Rolled vs. Ground ballscrews
juan gelt
2005-09-18 17:53:57 UTC
Re: [CAD_CAM_EDM_DRO] Rolled vs. Ground ballscrews
juan gelt
2005-09-18 17:54:16 UTC
Re: [CAD_CAM_EDM_DRO] Rolled vs. Ground ballscrews
R Rogers
2005-09-18 18:05:20 UTC
Re: [CAD_CAM_EDM_DRO] Rolled vs. Ground ballscrews
cstrudwicke@o...
2005-09-18 18:13:01 UTC
Re: [CAD_CAM_EDM_DRO] Rolled vs. Ground ballscrews
juan gelt
2005-09-18 18:17:56 UTC
Re: [CAD_CAM_EDM_DRO] Rolled vs. Ground ballscrews or other screws!
Steve Haushahn
2005-09-18 19:42:09 UTC
Re: [CAD_CAM_EDM_DRO] Rolled vs. Ground ballscrews or other screws!
Les Newell
2005-09-19 01:29:12 UTC
Re: [CAD_CAM_EDM_DRO] Rolled vs. Ground ballscrews
Les Newell
2005-09-19 01:36:23 UTC
Re: [CAD_CAM_EDM_DRO] Rolled vs. Ground ballscrews
juan gelt
2005-09-19 05:39:17 UTC
Re: [CAD_CAM_EDM_DRO] Rolled vs. Ground ballscrews
Andy Wander
2005-09-19 06:27:34 UTC
RE: [CAD_CAM_EDM_DRO] Rolled vs. Ground ballscrews or other screws!
George Taylor, IV
2005-09-19 10:54:19 UTC
Re: [CAD_CAM_EDM_DRO] Rolled vs. Ground ballscrews or other screws!
Dan Mauch
2005-09-19 11:11:16 UTC
Re: [CAD_CAM_EDM_DRO] Rolled vs. Ground ballscrews or other screws!
George Taylor, IV
2005-09-19 11:40:27 UTC
Re: [CAD_CAM_EDM_DRO] Rolled vs. Ground ballscrews or other screws!
Polaraligned
2005-09-19 14:49:19 UTC
Re: Rolled vs. Ground ballscrews or other screws!
Andy Wander
2005-09-19 15:05:29 UTC
RE: [CAD_CAM_EDM_DRO] Rolled vs. Ground ballscrews or other screws!
turbulatordude
2005-09-19 16:07:32 UTC
Re: Rolled vs. Ground ballscrews or other screws!
Lance Hopper
2005-09-19 19:49:40 UTC
Re: Rolled vs. Ground ballscrews or other screws!
George Taylor, IV
2005-09-19 21:38:42 UTC
RE: [CAD_CAM_EDM_DRO] Re: Rolled vs. Ground ballscrews or other screws!
George Taylor, IV
2005-09-19 21:39:17 UTC
RE: [CAD_CAM_EDM_DRO] Rolled vs. Ground ballscrews or other screws!
turbulatordude
2005-09-19 22:08:11 UTC
Re: Rolled vs. Ground ballscrews or other screws!
Lance Hopper
2005-09-20 05:18:16 UTC
Re: Rolled vs. Ground ballscrews or other screws!
leslie watts
2005-09-20 05:44:25 UTC
RE: [CAD_CAM_EDM_DRO] Re: Rolled vs. Ground ballscrews or other screws!
Fred Smith
2005-09-20 07:10:36 UTC
Re: Rolled vs. Ground ballscrews or other screws!
turbulatordude
2005-09-20 09:49:18 UTC
Re: Rolled vs. Ground ballscrews or other screws!
Lance Hopper
2005-09-20 11:54:58 UTC
Re: Rolled vs. Ground ballscrews or other screws!
Raymond Heckert
2005-09-20 21:13:24 UTC
Re: [CAD_CAM_EDM_DRO] Rolled vs. Ground ballscrews or other screws!
Jim Colley
2005-09-21 17:41:17 UTC
Re: Rolled vs. Ground ballscrews
Lance Hopper
2005-09-22 05:47:12 UTC
Re: Rolled vs. Ground ballscrews