CAD CAM EDM DRO - Yahoo Group Archive

Re: SPINDLE INDEX PULSE

Posted by lcdpublishing
on 2006-05-12 14:32:32 UTC
Bill,

The encoder wheel can be any resolution, but, there needs to be
one "marker spot" on the wheel for the index signal for threading.
I believe you could get away with a single slotted disc. I believe
this is also why the other suggestion of a 90 "degree slot", to make
sure there is only one spot on the disc for mach to sense for thread
start.

I made a disc for my spindle on the router that used 3 slots as I
needed 3:1 ratio - worked fine on the mill software.

Chris


--- In CAD_CAM_EDM_DRO@yahoogroups.com, wanliker@... wrote:
>
>
> In a message dated 5/12/2006 2:57:05 P.M. Mountain Daylight Time,
> rogersmach@... writes:
>
> used with like a 90 degree section missing
>
>
> That would be a horrible disc, something has to be wrong to need
that. IMHO
>
> bill
>
>
> [Non-text portions of this message have been removed]
>

Discussion Thread

wanliker@a... 2006-05-12 12:32:10 UTC SPINDLE INDEX PULSE Alan Marconett 2006-05-12 13:38:17 UTC RE: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE wanliker@a... 2006-05-12 13:42:37 UTC Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE R Rogers 2006-05-12 13:56:14 UTC Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE wanliker@a... 2006-05-12 14:04:24 UTC Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE wanliker@a... 2006-05-12 14:05:57 UTC SPINDLE INDEX PULSE Alan Marconett 2006-05-12 14:32:18 UTC RE: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE lcdpublishing 2006-05-12 14:32:32 UTC Re: SPINDLE INDEX PULSE R Rogers 2006-05-12 15:55:24 UTC Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE R Rogers 2006-05-12 16:01:36 UTC Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE wanliker@a... 2006-05-12 16:09:29 UTC Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE Dan Mauch 2006-05-12 16:26:14 UTC Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE R Rogers 2006-05-12 16:45:59 UTC Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE Dan Mauch 2006-05-12 21:01:51 UTC Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE Peter Homann 2006-05-12 21:44:30 UTC Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE Alan Marconett 2006-05-13 08:52:36 UTC Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE roboticscnc 2006-05-13 09:18:24 UTC Re: SPINDLE INDEX PULSE Arturo E. Duncan 2006-05-13 15:59:04 UTC Re: SPINDLE INDEX PULSE wanliker@a... 2006-05-13 20:40:31 UTC SPINDLE INDEX PULSE wanliker@a... 2006-05-15 00:52:24 UTC SPINDLE INDEX PULSE Paul Kelly 2006-05-15 01:13:37 UTC RE: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE wanliker@a... 2006-05-18 13:40:59 UTC SPINDLE INDEX PULSE