Re: SPINDLE INDEX PULSE
Posted by
roboticscnc
on 2006-05-13 09:18:24 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, wanliker@... wrote:
perfectly with Mach 3 for screwcutting.
The disk I'm using is about 60mm diameter with a 2.5mm wide slot( 2
hacksaw cuts as close as I could cut them and filed ).
I'm only screwcutting M16x2 threads at around 350 RPM ( until I get a
carbide screwcutting tool ) and allowing 20mm movement of the carriage
before reaching the material to make sure the axis has finished
accellerating. This is probably excessive but I'm not mass producing.
Hope this helps,
Regards,
Glen.
>using
> Has anyone on the list made an spindle disc, to mount on a Sherline,
> the CNC4PC board, for use with Mach3?I'm using the CNC4PC Index Pulse Card on my lathe and it works
>
> If you have,could you give some details?
>
> 1. How many Holes on it?
>
> 2. What diameter hole/slots, did you use?
>
> 3. How did you mount the spindle disc on the Sherline?
>
> 4. Any problems?
>
> 5. Any suggestions as to how you would improve your efforts?
>
> 6. Have you used it for threading with Mach3 yet? Results?
>
> 7. Whatever, I forgot to ask???
>
> Thanks,
> bill
>
>
> [Non-text portions of this message have been removed]
>
perfectly with Mach 3 for screwcutting.
The disk I'm using is about 60mm diameter with a 2.5mm wide slot( 2
hacksaw cuts as close as I could cut them and filed ).
I'm only screwcutting M16x2 threads at around 350 RPM ( until I get a
carbide screwcutting tool ) and allowing 20mm movement of the carriage
before reaching the material to make sure the axis has finished
accellerating. This is probably excessive but I'm not mass producing.
Hope this helps,
Regards,
Glen.
Discussion Thread
wanliker@a...
2006-05-12 12:32:10 UTC
SPINDLE INDEX PULSE
Alan Marconett
2006-05-12 13:38:17 UTC
RE: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE
wanliker@a...
2006-05-12 13:42:37 UTC
Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE
R Rogers
2006-05-12 13:56:14 UTC
Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE
wanliker@a...
2006-05-12 14:04:24 UTC
Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE
wanliker@a...
2006-05-12 14:05:57 UTC
SPINDLE INDEX PULSE
Alan Marconett
2006-05-12 14:32:18 UTC
RE: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE
lcdpublishing
2006-05-12 14:32:32 UTC
Re: SPINDLE INDEX PULSE
R Rogers
2006-05-12 15:55:24 UTC
Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE
R Rogers
2006-05-12 16:01:36 UTC
Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE
wanliker@a...
2006-05-12 16:09:29 UTC
Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE
Dan Mauch
2006-05-12 16:26:14 UTC
Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE
R Rogers
2006-05-12 16:45:59 UTC
Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE
Dan Mauch
2006-05-12 21:01:51 UTC
Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE
Peter Homann
2006-05-12 21:44:30 UTC
Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE
Alan Marconett
2006-05-13 08:52:36 UTC
Re: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE
roboticscnc
2006-05-13 09:18:24 UTC
Re: SPINDLE INDEX PULSE
Arturo E. Duncan
2006-05-13 15:59:04 UTC
Re: SPINDLE INDEX PULSE
wanliker@a...
2006-05-13 20:40:31 UTC
SPINDLE INDEX PULSE
wanliker@a...
2006-05-15 00:52:24 UTC
SPINDLE INDEX PULSE
Paul Kelly
2006-05-15 01:13:37 UTC
RE: [CAD_CAM_EDM_DRO] SPINDLE INDEX PULSE
wanliker@a...
2006-05-18 13:40:59 UTC
SPINDLE INDEX PULSE