Re: [CAD_CAM_EDM_DRO] Re: Sherline Problem
Posted by
hannu
on 2007-11-08 10:03:51 UTC
You only need one pulse for threading. This is well established.
I recommend putting another type of phototransistor on the spindle, a
reflective one.
Then paint one small reflective stripe on the spindle.
Many have done this with great results.
I did this, changin one phototransistor (for a slotted disc like yours)
for another.
I put a piece of aluminum foil on thespindle with tape, works fine.
Cost 11 € for a single ir phototransistor, locally. Qty prices are 1-3
$. Worked the same day.
What electronics are you using to connect the spindle index pulse to
your pc ?
I may have an part number. There are many options, it was really much
easier than I thought.
h.
I recommend putting another type of phototransistor on the spindle, a
reflective one.
Then paint one small reflective stripe on the spindle.
Many have done this with great results.
I did this, changin one phototransistor (for a slotted disc like yours)
for another.
I put a piece of aluminum foil on thespindle with tape, works fine.
Cost 11 € for a single ir phototransistor, locally. Qty prices are 1-3
$. Worked the same day.
What electronics are you using to connect the spindle index pulse to
your pc ?
I may have an part number. There are many options, it was really much
easier than I thought.
h.
>
> In a message dated 11/7/2007 11:55:54 A.M. Mountain Standard Time,
> hvenermo@... <mailto:hvenermo%40amorco.com> writes:
>
> Use a left-handed drill to drill it out ?
>
> *
> *
> *
>
> I have used left hand drills for a long time, but they have trouble with
> the hardened set screws. If the set screw is broken sometimes they
> will catch
> on the cracks on the top, but in this case there are no cracks.
>
> I was going to take it off, so I could mount a disc on the side for
> putting
> out the pulse that Mach needs for threading.
> So I am now looking at other options so I can just forget the set
> screw is
> there.
> bill
>
Discussion Thread
wanliker@a...
2007-11-07 00:38:08 UTC
Sherline Problem
Preston Petty
2007-11-07 02:06:25 UTC
Re: Sherline Problem
Edward Valpey
2007-11-07 05:34:12 UTC
Re: [CAD_CAM_EDM_DRO] Sherline Problem
Peter Reilley
2007-11-07 07:27:48 UTC
Re: [CAD_CAM_EDM_DRO] Sherline Problem
Russ Waters
2007-11-07 08:12:58 UTC
Re: [CAD_CAM_EDM_DRO] Sherline Problem
Drew Rogge
2007-11-07 08:45:48 UTC
Re: [CAD_CAM_EDM_DRO] Sherline Problem
Jon Elson
2007-11-07 10:19:06 UTC
Re: [CAD_CAM_EDM_DRO] Sherline Problem
wanliker@a...
2007-11-07 10:19:20 UTC
Sherline Problem
Andy Wander
2007-11-07 10:22:13 UTC
RE: [CAD_CAM_EDM_DRO] Sherline Problem
Jim DuBois
2007-11-07 10:30:10 UTC
RE: [CAD_CAM_EDM_DRO] Sherline Problem
Chris Brown
2007-11-07 10:42:22 UTC
Re: Sherline Problem
David G. LeVine
2007-11-07 10:50:39 UTC
Re: [CAD_CAM_EDM_DRO] Sherline Problem
hannu
2007-11-07 10:55:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Sherline Problem
wanliker@a...
2007-11-07 13:33:18 UTC
Sherline Problem
wanliker@a...
2007-11-07 14:48:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: Sherline Problem
wanliker@a...
2007-11-07 14:56:06 UTC
Re: [CAD_CAM_EDM_DRO] Sherline Problem
jeetendra_g10
2007-11-08 05:54:25 UTC
Re: Sherline Problem
hannu
2007-11-08 10:03:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Sherline Problem
jesse Brennan
2007-11-08 11:29:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Sherline Problem
Andy Wander
2007-11-08 11:40:06 UTC
RE: [CAD_CAM_EDM_DRO] Re: Sherline Problem
David G. LeVine
2007-11-08 18:53:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: Sherline Problem