Re: Programming Slo-Syn SS20001 with SS2000D6
Posted by
opscimc
on 2012-04-23 09:28:02 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Jon Elson <elson@...> wrote:
Have said the above about it being one-time, should it be possible to control these stepper controllers from an already-written interface (e.g. Mach3) with no more effort (or, ideally, a lot less) than brute force programming of the Slo-Syn SS20001, being able to do so would open up other possibilities.
> Due to battery, thermal and power management, laptops are not a goodThe specific application I have in mind isn't full control of either my lathe or mill, but rather to use a stepper to "simply" drag my lathe's cross slide a tiny bit further part way through cutting a taper (i.e. to make a more complex form for the taper). After I finally succeed (which involves achieving a tolerance no worse than 0.0002"), I only need to make one piece, after which I will remove this assembly. Because of this, a laptop makes more sense for me right now than trying to make space in a reasonable place to intstall a desktop computer where it won't get covered with chips and oil.
> choice for
> real-time motion control.
>
Have said the above about it being one-time, should it be possible to control these stepper controllers from an already-written interface (e.g. Mach3) with no more effort (or, ideally, a lot less) than brute force programming of the Slo-Syn SS20001, being able to do so would open up other possibilities.
Discussion Thread
opscimc
2012-04-20 20:59:05 UTC
Programming Slo-Syn SS20001 with SS2000D6
kirk
2012-04-21 08:36:40 UTC
Re: Programming Slo-Syn SS20001 with SS2000D6
opscimc
2012-04-22 07:25:03 UTC
Re: Programming Slo-Syn SS20001 with SS2000D6
turbulatordude
2012-04-22 08:02:01 UTC
Re: Programming Slo-Syn SS20001 with SS2000D6
opscimc
2012-04-22 08:50:09 UTC
Re: Programming Slo-Syn SS20001 with SS2000D6
Jon Elson
2012-04-22 20:53:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Programming Slo-Syn SS20001 with SS2000D6
opscimc
2012-04-22 21:26:57 UTC
Re: Programming Slo-Syn SS20001 with SS2000D6
Andy Wander
2012-04-22 21:42:29 UTC
RE: [CAD_CAM_EDM_DRO] Re: Programming Slo-Syn SS20001 with SS2000D6
opscimc
2012-04-22 21:55:41 UTC
Re: Programming Slo-Syn SS20001 with SS2000D6
Ron Thompson
2012-04-23 07:35:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Programming Slo-Syn SS20001 with SS2000D6
Jon Elson
2012-04-23 08:41:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Programming Slo-Syn SS20001 with SS2000D6
Jon Elson
2012-04-23 08:43:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Programming Slo-Syn SS20001 with SS2000D6
opscimc
2012-04-23 09:28:02 UTC
Re: Programming Slo-Syn SS20001 with SS2000D6
opscimc
2012-04-23 12:20:18 UTC
Re: Programming Slo-Syn SS20001 with SS2000D6
David G. LeVine
2012-04-23 14:04:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Programming Slo-Syn SS20001 with SS2000D6
Jon Elson
2012-04-23 18:19:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Programming Slo-Syn SS20001 with SS2000D6
opscimc
2012-04-23 19:30:16 UTC
Re: Programming Slo-Syn SS20001 with SS2000D6
Andy Wander
2012-04-24 06:46:03 UTC
RE: [CAD_CAM_EDM_DRO] Re: Programming Slo-Syn SS20001 with SS2000D6
Jon Elson
2012-04-24 09:20:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Programming Slo-Syn SS20001 with SS2000D6
opscimc
2012-04-24 12:23:55 UTC
Re: Programming Slo-Syn SS20001 with SS2000D6
Andy Wander
2012-04-24 12:52:39 UTC
RE: [CAD_CAM_EDM_DRO] Re: Programming Slo-Syn SS20001 with SS2000D6
alenz@b...
2012-04-24 18:57:47 UTC
Re: Programming Slo-Syn SS20001 with SS2000D6