Re: [CAD_CAM_EDM_DRO] Re: Grizzly G1006 Mill CNC???
Posted by
jeremy youngs
on 2012-10-10 21:49:14 UTC
see previous post i recommended a 450 give or take also should have
mentioned to get it in nema 23 if possible as the smaller the package the
faster it will move
mentioned to get it in nema 23 if possible as the smaller the package the
faster it will move
On Thu, Oct 11, 2012 at 12:44 AM, Tony Smith <ajsmith1968@...> wrote:
> **
>
>
> > > This is one case where you many not actually get what you're paying
> > > for. Or think you're paying for.
> > >
> > >
> > steppers are rated as holding torque so you are in fact getting exactly
> what you
> > payed for
>
> Well, I'll just make sure I never move anything.
>
> If you think a 1200 oz-in stepper will perform better than a 450 oz-in one
> based on those numbers alone, then you thought wrong.
>
> As before, read the datasheet.
>
> Tony
>
>
>
--
jeremy youngs
[Non-text portions of this message have been removed]
Discussion Thread
Armilite@a...
2012-10-07 17:28:28 UTC
Grizzly G1006 Mill CNC???
jeremy youngs
2012-10-07 21:29:51 UTC
Re: [CAD_CAM_EDM_DRO] Grizzly G1006 Mill CNC???
Dave Halliday
2012-10-07 21:30:45 UTC
RE: [CAD_CAM_EDM_DRO] Grizzly G1006 Mill CNC???
Armilite@a...
2012-10-08 06:09:33 UTC
Grizzly G1006 Mill CNC???
jeremy youngs
2012-10-08 10:28:46 UTC
Re: [CAD_CAM_EDM_DRO] Grizzly G1006 Mill CNC???
Dave Sage
2012-10-09 18:55:13 UTC
Re: Grizzly G1006 Mill CNC???
jeremy youngs
2012-10-09 20:19:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: Grizzly G1006 Mill CNC???
Dan Mauch
2012-10-10 06:59:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Grizzly G1006 Mill CNC???
Tony Smith
2012-10-10 14:07:15 UTC
RE: [CAD_CAM_EDM_DRO] Re: Grizzly G1006 Mill CNC???
Alexander SS
2012-10-10 17:15:57 UTC
V MILL puzzle
jeremy youngs
2012-10-10 21:22:11 UTC
Re: [CAD_CAM_EDM_DRO] V MILL puzzle
jeremy youngs
2012-10-10 21:25:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Grizzly G1006 Mill CNC???
Tony Smith
2012-10-10 21:44:37 UTC
RE: [CAD_CAM_EDM_DRO] Re: Grizzly G1006 Mill CNC???
jeremy youngs
2012-10-10 21:49:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Grizzly G1006 Mill CNC???
Tony Smith
2012-10-10 22:18:12 UTC
RE: [CAD_CAM_EDM_DRO] Re: Grizzly G1006 Mill CNC???
jeremy youngs
2012-10-10 22:22:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Grizzly G1006 Mill CNC???
Ron Thompson
2012-10-11 06:12:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Grizzly G1006 Mill CNC???
Tony Smith
2012-10-11 09:35:44 UTC
RE: [CAD_CAM_EDM_DRO] Re: Grizzly G1006 Mill CNC???
jeremy youngs
2012-10-11 09:47:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Grizzly G1006 Mill CNC???
Tony Smith
2012-10-11 10:09:35 UTC
RE: [CAD_CAM_EDM_DRO] Re: Grizzly G1006 Mill CNC???
Dave Sage
2012-10-13 06:25:09 UTC
Re: Grizzly G1006 Mill CNC???
jeremy youngs
2012-10-13 14:27:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: Grizzly G1006 Mill CNC???