RE: [CAD_CAM_EDM_DRO] Re: 3D Printing
Posted by
Dan Mauch
on 2012-12-18 09:34:14 UTC
Load the 3dprinter.xml into mach3 that I emailed you a few minutes ago and
take a look at the motor tuning information relative to steps per unit and
velocity. I used a G540 which have ten micro step drivers. The stepper was
direct coupled to a 5 TPI ballscrew. One of the most important aspects of a
retrofit should be zero back lash on the XY axes.
Dan Mauch
www.camtronics-cnc.com
dmauch@...
Stepper and servo motors
Kits, assembled and custom CNC using Gecko products.
[Non-text portions of this message have been removed]
take a look at the motor tuning information relative to steps per unit and
velocity. I used a G540 which have ten micro step drivers. The stepper was
direct coupled to a 5 TPI ballscrew. One of the most important aspects of a
retrofit should be zero back lash on the XY axes.
Dan Mauch
www.camtronics-cnc.com
dmauch@...
Stepper and servo motors
Kits, assembled and custom CNC using Gecko products.
[Non-text portions of this message have been removed]
Discussion Thread
dampfloken
2007-05-07 00:15:16 UTC
3D Printing
Graham Stabler
2007-05-07 04:25:28 UTC
Re: 3D Printing
James Cullins
2007-05-07 05:21:09 UTC
Re: [CAD_CAM_EDM_DRO] 3D Printing
ebiz_59
2012-07-09 21:54:17 UTC
3D Printing
Jon Elson
2012-07-10 08:54:51 UTC
Re: [CAD_CAM_EDM_DRO] 3D Printing
Mars Bonfire
2012-07-11 15:09:01 UTC
Re: 3D Printing
callcbm Enjen joes
2012-07-11 17:19:02 UTC
RE: [CAD_CAM_EDM_DRO] 3D Printing
Drew
2012-07-12 06:40:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: 3D Printing
Jack McKie
2012-07-12 07:42:58 UTC
Re: [CAD_CAM_EDM_DRO] Re: 3D Printing
Craig Carmichael
2012-07-12 09:13:12 UTC
Re: [CAD_CAM_EDM_DRO] Conductive ABS -- 3D Printing
Drew Rogge
2012-07-12 09:47:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: 3D Printing
Drew
2012-07-12 16:39:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: 3D Printing
Gary Crowell
2012-07-12 16:40:15 UTC
Re: [CAD_CAM_EDM_DRO] Conductive ABS -- 3D Printing
Drew
2012-07-13 10:32:55 UTC
Re: [CAD_CAM_EDM_DRO] Conductive ABS -- 3D Printing
Craig Carmichael
2012-07-15 11:22:55 UTC
Re: [CAD_CAM_EDM_DRO] Conductive ABS -- 3D Printing
Mark Bingham
2012-07-24 15:42:57 UTC
Re: [CAD_CAM_EDM_DRO] Conductive ABS -- 3D Printing
Dan Mauch
2012-12-18 07:56:07 UTC
Re: 3D Printing
John Dammeyer
2012-12-18 09:09:45 UTC
RE: [CAD_CAM_EDM_DRO] Re: 3D Printing
Dan Mauch
2012-12-18 09:34:14 UTC
RE: [CAD_CAM_EDM_DRO] Re: 3D Printing
John Dammeyer
2012-12-18 09:48:41 UTC
RE: [CAD_CAM_EDM_DRO] Re: 3D Printing
John Dammeyer
2012-12-18 09:48:44 UTC
RE: [CAD_CAM_EDM_DRO] Re: 3D Printing
samcoinc2001
2012-12-18 14:29:36 UTC
Re: 3D Printing
Tony Smith
2012-12-18 19:34:29 UTC
RE: [CAD_CAM_EDM_DRO] Re: 3D Printing
Ron Thompson
2012-12-18 21:37:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: 3D Printing
Tony Smith
2012-12-18 23:02:55 UTC
RE: [CAD_CAM_EDM_DRO] Re: 3D Printing
Ron Thompson
2012-12-19 07:09:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: 3D Printing
samcoinc2001
2012-12-19 16:12:23 UTC
Re: 3D Printing
Tony Smith
2012-12-19 22:12:43 UTC
RE: [CAD_CAM_EDM_DRO] Re: 3D Printing