CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Casting clearance

Posted by Jon Anderson
on 2000-10-13 07:24:44 UTC
Steve Gunsel wrote:
>
> It seems that the surface of the screw threads is the determining
> factor and that it should be carefully lapped to remove as much of
> the imperfection as possible prior to casting the nut.

Someone mentioned Carnuba wax earlier, I really don't think this by
itself would make a good release agent. However, it's a pretty hard wax,
and might do a good job of filling in imperfections.
Maybe the best approach would be a light lapping with a brass female lap
to remove any high spots and micro burrs, followed by a good cleaning,
then Carnuba wax to try to fill in the micro pits.

I've got a microscope in the shop, and it's amazing how poor the surface
of even a ground screw can look if you look close enough...

Jon

Discussion Thread

Carey L. Culpepper 2000-10-12 07:12:17 UTC Re: [CAD_CAM_EDM_DRO] Re:Casting clearance Ron Ginger 2000-10-12 07:19:03 UTC Re: [CAD_CAM_EDM_DRO] Re:Casting clearance Jon Anderson 2000-10-12 07:39:06 UTC Re: [CAD_CAM_EDM_DRO] Re:Casting clearance Jon Anderson 2000-10-12 07:44:40 UTC Re: [CAD_CAM_EDM_DRO] Re:Casting clearance Carey L. Culpepper 2000-10-12 08:03:19 UTC Re: [CAD_CAM_EDM_DRO] Re:Casting clearance Jon Anderson 2000-10-12 08:34:04 UTC Re: [CAD_CAM_EDM_DRO] Re:Casting clearance Ron Ginger 2000-10-12 08:36:43 UTC Re:Casting clearance Ray 2000-10-12 09:31:43 UTC Re: Re: Re:Casting clearance Jon Anderson 2000-10-12 09:49:59 UTC Re: [CAD_CAM_EDM_DRO] Re:Casting clearance ballendo@y... 2000-10-12 12:42:49 UTC Re: Re:Casting clearance ballendo@y... 2000-10-12 12:49:48 UTC Re: Re:Casting clearance ballendo@y... 2000-10-12 12:51:36 UTC Re: Re:Casting clearance ballendo@y... 2000-10-12 12:57:12 UTC Re: Re:Casting clearance ballendo@y... 2000-10-12 14:21:24 UTC Re: Re: Re:Casting clearance A. G. Eckstein 2000-10-12 15:30:59 UTC Re: [CAD_CAM_EDM_DRO] Re:Casting clearance Ron Ginger 2000-10-13 05:46:45 UTC Re: Casting clearance Steve Gunsel 2000-10-13 07:12:30 UTC Re: [CAD_CAM_EDM_DRO] Re: Casting clearance Jon Anderson 2000-10-13 07:24:44 UTC Re: [CAD_CAM_EDM_DRO] Re: Casting clearance Kevin P. Martin 2000-10-13 07:41:53 UTC RE: [CAD_CAM_EDM_DRO] Re: Casting clearance Ron Ginger 2000-10-13 07:59:43 UTC Re: [CAD_CAM_EDM_DRO] Re: Casting clearance Tim Goldstein 2000-10-13 09:21:45 UTC RE: [CAD_CAM_EDM_DRO] Re: Casting clearance Jon Anderson 2000-10-13 09:57:04 UTC Re: [CAD_CAM_EDM_DRO] Re: Casting clearance Anne Ogborn 2000-10-13 12:00:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Casting clearance Jon Elson 2000-10-13 14:44:37 UTC Re: [CAD_CAM_EDM_DRO] Re: Casting clearance Kevin P. Martin 2000-10-16 13:03:07 UTC RE: [CAD_CAM_EDM_DRO] Re: Casting clearance