Re: [CAD_CAM_EDM_DRO] virtual hand jive
Posted by
Anne Ogborn
on 2000-11-06 13:00:11 UTC
ON a slight, but only slight, side note,
I build model railroads, and we're constantly needing "turn
this shaft here and make that turn over there".
One solution I've used is to wire two permag motors in parallel
(no power supply). When one motor turns, the other turns more or
less with it. If you put a spur gear based reduction on each one
you'll find they more or less stay in synch, at least well enough
for a manual control.
I build model railroads, and we're constantly needing "turn
this shaft here and make that turn over there".
One solution I've used is to wire two permag motors in parallel
(no power supply). When one motor turns, the other turns more or
less with it. If you put a spur gear based reduction on each one
you'll find they more or less stay in synch, at least well enough
for a manual control.
Discussion Thread
jmw@c...
2000-11-06 12:03:23 UTC
virtual hand jive
Jon Anderson
2000-11-06 12:20:56 UTC
Re: [CAD_CAM_EDM_DRO] virtual hand jive
Rick Dulas
2000-11-06 12:32:48 UTC
Re: [CAD_CAM_EDM_DRO] virtual hand jive
Alan Marconett KM6VV
2000-11-06 12:51:25 UTC
Re: [CAD_CAM_EDM_DRO] virtual hand jive
Wally K
2000-11-06 12:57:25 UTC
Re: virtual hand jive
Anne Ogborn
2000-11-06 13:00:11 UTC
Re: [CAD_CAM_EDM_DRO] virtual hand jive
Joe Vicars
2000-11-06 13:16:50 UTC
Re: [CAD_CAM_EDM_DRO] virtual hand jive
Smoke
2000-11-06 13:42:17 UTC
Re: [CAD_CAM_EDM_DRO] virtual hand jive
jmw@c...
2000-11-06 13:43:46 UTC
Re: virtual hand jive
Alan Marconett KM6VV
2000-11-06 18:47:21 UTC
Re: virtual hand jive
ballendo@y...
2000-11-06 19:23:17 UTC
Re: virtual hand jive
Alan Marconett KM6VV
2000-11-06 20:09:02 UTC
Re: virtual hand jive
Anne Ogborn
2000-11-06 22:28:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: virtual hand jive
ballendo@y...
2000-11-07 01:22:23 UTC
Re: Re: virtual hand jive
Smoke
2000-11-07 06:42:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: virtual hand jive
Jon Anderson
2000-11-07 09:00:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: virtual hand jive
Andrew Werby
2000-11-07 10:08:55 UTC
Re: virtual hand jive
Alan Marconett KM6VV
2000-11-07 11:28:15 UTC
Re: virtual hand jive
Alan Marconett KM6VV
2000-11-07 11:36:57 UTC
Re: virtual hand jive
Jon Elson
2000-11-07 12:05:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: virtual hand jive
ballendo@y...
2000-11-07 14:14:28 UTC
Re: Re: virtual hand jive
Smoke
2000-11-07 15:45:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: virtual hand jive
ballendo@y...
2000-11-07 16:25:55 UTC
Re: virtual hand jive
ballendo@y...
2000-11-07 20:24:07 UTC
Re: Re: Re: virtual hand jive